2. SAE 30 oil (T- 100°F) flows through the 2-in diameter pipe shown. At Point B,...
Clean engine oil is pumped through a pipe %)n, in diameter and 10 ft long, as shown. Pressure is atmospheric both at the inlet to the pump and at the exit from the pipe. The average velocity of the oil is 1.5 ft/s Assuming fully-developed laminar tlow, calculate the pressure rise across the pump (in psia) and the power input of the pump (in hp) if the oil temperature is a) 70°F 4. b) 40°F atn Clean engine oil is...
1) 2) 3) Oil flows through an 8-inch diameter pipe with a velocity of 18 ft/s. If it discharges into the atmosphere through the nozzle, determine the total force the bolts must resist at the connection AB to hold the nozzle onto the pipe. Assume Yo = 55 lb/ft3. (30 pts) 8 in. 4 in. 18 m/s 06 PROB011 Research is being conducted on a medical specimen. They are trying to determine the pressure drop in fluid carrying vessels. If...
5. Oil Flow in a Pipe Oil (S 0.80;0.01 lb s ft-2) flows downward in the pipe shown in Figure 3. The pipe diameter is 0.10 ft and has a slope of 30°. The mean fluid velocity is 3 ft s1. What is the pressure gradient, de, along the length of the pipe? 30° Figure 3: Schematic of oil flow in a pipe. Answer(s):-71 lb ft-2 ft-1
6-7. Oil flows through the 100-mm-diameter pipe with a velocity of 8 m/s. If the pressure in the pipe at A and B is assumed to be 60 kPa, determine the x and y components of force the flow exerts on the elbow. The flow occurs in the horizontal plane. Take ρο -900 kg/m3 8 m/s 30° 100 mm 100 mm
Water flows through a 30° pipe bend at a rate of 200 gpm. The diameter of the entrance to the bend is 2.5 in. and that of the exit is 3 in. The pressure in the pipe is 30 psig, and the pressure drop in the bend is negligible. What is the total force (magnitude and direction) exerted by the fluid on the pipe bend?
24.) (2) point Water at T = 30°C flows through the 400-mm-diameter concrete pipe from the reservoir at A to the one at B. Determine the flow. The length of the concrete pipe is 100 m. The roughness of the concrete pipe is e = 0.8 mm. А +15 m B
(c) Fuel oil, with a density of 870 kg m-, is pumped through a horizontal pipe, as shown in Figure Q2.2. The pipe is 100 mm in diameter and contains an orifice plate with a throat diameter of 40 mm. The pressure drop across the orifice is measured on a U-tube manometer, containing mercury with a specific gravity 13.6. The difference in levels of the columns is measured as 45 mm. The coefficient of discharge for the orifice plate Ca...
DON’T disregard the thermal conductivity of the pipe 3.) Oil at 200 C flows in a pipeline. The pipe has a 30-cm diameter and the flow is at an average velocity of 2 m/s. A 200-m-long section of the pipeline passes through icy waters of a lake at 0° C. The pipe is uncoated carbon steel with a thermal conductivity of 61 W/m o C. Determine (a) the temperature of the oil when the pipe leaves the lake, (b) the...
Problem 2: Oil at 20 °C (SG 0.88) flows in the 3-cm P= 180 kPa diameter pipe shown in the figure. For the pressure measurements in the figure, determine: a) Whether the flow is up or down b) The head loss between points A and B P 500 kPa 15 m c) The flow rate if losses are about 16% of the 370 velocity head 20 m Problem 2: Oil at 20 °C (SG 0.88) flows in the 3-cm P=...
3. Oil flows in the pipe shown. The orifice in the pipe has a coefficient of discharge of 0.64. Compute the discharge of the oil in the pipe CE311 Fluid Mechanics Winter 2019, Assignment 5, Due March 1 4. Water flows steadily through the funnel shown in the figure below. Throughout most of the funnel the flow is approximately radial (along rays from O) with a velocity of V- cr where r is the radial coordinate and c is a...