ler needs of an office are Met by estinj tab water Ly a hest pump from...
A farmer needs to purchase a pump to bring water from a well at a rate of 4 L/s to irrigate his crops. The water table in the aquifer is at a depth 20 m below the ground surface at the extraction site. From the extraction site, water is pumped to a storage tank located 58 m above the well. Altogether, the needed piping has a length of 420 m and all lines are 5 cm plastic piping. There are...
Please show detailed work and write clearly.Thank you.
A chilled-water system requires a 100 gal/min pump with 40 ftWG of head. Select the most appropriate pump from the pump curves in the figure below. State the efficiency, motor power input, impeller size, and NPSH requirement for your selection. Note that the pump may not be a precise match to the specified flow condition Capacity (L/s) 10 12 18 60% 40% 50%: 55%,65% о, 68% 67% 7" 1750 50 68% 12...
A water tower is fed from an underground water source (Figure 2). The difference in level is 67 m. The flow of water must be at least 55 m'/h. To provide this flow (55m/h), a pump must be driven at a speed of 690 RPM. It can turn faster, but without exceeding 900 RPM. Its efficiency is 81%. The pump is driven directly, therefore without gearbox, by an asynchronous motor, which itselif is supplied directly by the 400V/50 Hz three-phase...
A reheat power plant operates between the pressures of 10 MPa and 5 kPa. Steam enters the high and low pressure turbines at 400 °C. If the steam leaves the high pressure turbine at 4 MPa and steam is at saturated vapour state at the end of both turbines, total specific power output of this power plant is; A heat pump is absorbing heat from the cold outdoors at 5°C and supplying heat to a house at 25°C at a...
HELP ME URGENT! Your father installed a pump to draw water from a well to your house water tank. The desired discharge is 70 L/s. He bought a pump (Pump 1) which delivers 2 kW of power to the water from a nearby hardware store. a) Evaluate whether the pump is adequate to deliver the desired flow rate to your house or not. b) Based on your evaluation, IF the pump is not sufficient to draw 70 L/s, propose a...
9-1 The above office requires 2,000,000 BTUH heating for exterior zones. A hot water heating system with a circulating pump is used for water circulation. Assume Heating coils have inlet temp 180 F outlet temp 140", and pump head is 30 FT. Answer the following questions: (3 points) (a) The required total hot water flow rate in GPM (b) BHP if the pump selected has an efficiency of 50% (c) what is the water main pipe size
9-1 The above...
QUESTION 5 A pump steadily delivers 17.2 kg/s of water at the conditions given below. Calculate the pump power (kW). There is no heat transfer from the pump to the surroundings (i.e., adiabatic conditions). Pump Inlet Temperature = 20°C Pump Inlet Pressure - 192 kPa Pump Inlet Diameter = 13.3 cm Pump Inlet Elevation = 22 m Pump Exit Temperature = 20°C Pump Exit Pressure - 419 kPa Pump Exit Diameter = 3.9 cm Pump Exit Elevation = 41.4 m...
When a water pump was tested at a rotation rate of 1500 rpm, the following data was obtained: Q (I/s) 0 10 20 30 40 50 H(m) 10.0 10.5 10.0 8.5 6.0 2.5 n (%) 0 0.40 0.64 0.72 0.64 0.40 It is proposed to use this pump to draw water from an open well and deliver it to a tank 5.5 m above. The delivery pipe is 20.0 m long and 100 mm diameter, and has a friction factor...
Q1
a) Company A designed a heat pump to
supply heat into a library in Canada during
winter, so that the library can maintain to be at 20°C. The heat
pump utilizes
12,000 L/min of Refrigerant-134a as the working fluid and absorb
heat from an
industrial water stream. The water stream enters the evaporator at
50°C and exits
at 25°C. The refrigerant enters the evaporator at 10°C with 90%
moisture content
and leaves at 20°C. There is no pressure drop in...
Problem 1: In the reservoir-pipe system below, water is supplied from reservoir A to reservoir B with a flowrate of 50 L/S. In the system, a pump with an efficiency value of n=0.70 is used. Length of the pipeline is L=5000m, pipe diameter is D=200 mm and the elevation difference between reservoirs is 40 m. According to this, a) Determine the required pump head (Hp). b) Find the required nominal pump power. c) Draw the relative energy grade line of...