) 25 points - Water flows in a piping system a section of which is shown...
The total length of the piping system made of cast iron providing hot water to a house is considered to have a 42m length with a constant diameter. The entrance gage pressure is 85 kPa and exit at 15 kPa gaged. Consider the water density equal 980 Kg/m' and the viscosity 1.138x10 Kg/ms. a) Compute the piping system diameter if the volumetric flow rate provided by this system is equal to 0.1 L/s. There is no pump present in this...
Example of Pipe Sizing The figure shows a closed piping system to supply chilled water to two heat exchangers. Size the pipe for this system, assuming schedule-40 steel pipe is used with threaded (screwed) fitting. Determine the pump flow rate and head requirements. Distances are as shown in feet. Head losses through the heat exchangers and chiller are shown as provided by the manufacturers. Q(gpm) Head Loss (ft) 70 Unit Chiller Heat Exchanger (a) 30 Heat Exchanger (b) 40 12...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı=0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is VÃ Pa = Pamb + y(30 m) р 2 and draw on the diagram the streamline you used. 2)...
A pipe system carries water from a reservoir and discharges it as a free jet, as shown. The system consists of piping made from 200-mm diameter commercial steel pipe with two 90 deg elbows with Kı= 0.4m and an inlet minor loss Kl = 0.05 1) (4 pts) Assuming ideal fluid model within the reservoir, show that pressure at point A is Vå Pa = Pamb + y(30 m) - p. 2 and draw on the diagram the streamline you...
A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as shown below (not to scale). The flow rate is controlled by two gate valves, the gate valve I controls the main pipeline, while the gate valve II controls the loop line from T-joint A to T-joint B. All pipes are galvanized steel pipe of diameter D = 4 in. It has a total length of Li2= 620 ft from tank 1 to tank 2....
Water with a velocity of 5m/s flows through the parallel concert piping system with a relative roughness of 0.04 shown below. The entrance diameter is 4m, the length of the parallel pipes is 40 m and L/d for the pipes at A and B is 10m. Here the pressure at the inlet of the system is measured by a mercury manometer directly below it. Given your understanding of the flow of incompressible fluids,notice the squared inlet edge and four standard...
(100 points) Water at 25°C is pumped at a rate of 0.075m's from a reservoir 20m above a pump to a free 1. discharge (this means discharged to atmosphere) 35m above the pump. The pressure on the intake side of the pump is 150kPa and the pressure on the discharge side of the pump is 450kPa. The pipe between the reservoir and the pump is 3 meters of Sin diameter cast iron. From the pump to the discharge the pipe...
1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...
1/9 1 Piping system (14 points) Water is pumped from a reservoir to a large receiver vessel which is maintained at p4 6 bar (absolute) through the operation of the pump and a high pressure nitrogen supply that bleeds into the tank through a regulator. The water enters through an opening at the top of the vessel. A drain is provided at the low point in the system. Elevations are as shown. All valves are gate valves (k = 0.15)...