A Newtonian fluid having a specific gravity of 0.9 and a kinematic viscosity of 0.000498 m...
, (20 pts) The Newtonian fluid is confined between an upper plate and a bottom f If its velocity profile is defined by u s(9y-0.1y3) rn m/s , where y is in mm, (a) determine the shear stress that the fluid exerts on the upper plate and bottom fixed surface and (b) indicate the direction of each shear stress. Take the fluid viscosity A0.482 N s/m2.
3. A Newtonian fluid with a dynamic or absolute viscosity of 0.38 Ns/m” and a Density of 910 kg/m flows through a 25 mm diameter pipe with a velocity of 2.6 m/s. Find out Reynolds number of the fluid. Is the fluid flow lamina, transient, or turbulent?
INFO GIVEN PROBLEM Consider a porous sphere sitting in a pool of stagnant Newtonian fluid (with constant viscosity μ). Liquid with constant viscosity μ is forced out radially from the sphere. Your ultimate goal is to find the velocity profile vi(r) of the liquid outside the sphere. The radius of the sphere is given by R. Assume the flow to be steady state; vo-Vo-0; and neglect gravity. Also, the velocity at the sphere surface is given by v(R)-Vo. Assume steady...
1. a. A fluid of density 1400 kg/mand viscosity of 0.9 kg/m.s flows through an 80 mm diameter pipe with a velocity of 5 m/s. What type of flow exists in the pipe? Justify your answer. (2 marks) b. A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil with kinematic viscosity v = 0.005...
A fluid having a viscosity u 9.35 x 104 lbf-s/ft is contained between two parallel plates, each of which has a cross section of 200 in2. The bottom plate is fixed whereas the top plate moves at a constant velocity of 4 ft/s when a shearing force is applied. The separation distance between the plates is a uniform 0.05 in. Assume the velocity distribution in the fluid is linear. Determine the following: 4. the shear stress in the fluid (lbf/in2)...
Fluid 7-The surface tension is phenomenon due to (a) Cohesion (b) Viscous force (c) Adhesion between liquid and solid molecules (d) Difference between the forces of adhesion and cohesion 8-The discharge 100 ft/min is equal to (a) 41.23 LUs (b) 45.23 L/s (c) 47.23 Ls (d) 49.23 L/s 9-Specific gravity is the relation between (a) the density of the fluid of specific material to the density of water at 4 °C (b) the density of the fluid of specific material...
2. The kinetic viscosity of a hydraulic oil is 110cP. The oil is flowing in a 20-mm diameter commercial steel pipe with the length of 45-m. If the velocity of oil is 4-m/s and specific gravity is 0.9 find the following a. Reynolds number b. Friction factor c. Head losses. 2. The kinetic viscosity of a hydraulic oil is 110cP. The oil is flowing in a 20-mm diameter commercial steel pipe with the length of 45-m. If the velocity of...
answer is 4.05(10^-5) N Problem 1: A Newtonian fluid is confined between the plate and a fixed surface. If the velocity profile is defined by u =(8y-0.3y) mm/s, where y is in mm, determine the force that must be applied to the plate to cause this motion. The plate has a surface area of 15 (10) mm in contact with the fluid. Use u = 0.482 (10) N.s/m(20 points) (8y-3.3y) du -0 T = Muy 72 (0.482 +5%) (8- 0.64)...
Consider the turbulent flow of air, density 1.2 kg/m3 and kinematic viscosity 1.5x10-5m2/s, through a channel bounded by two infinitely wide parallel plates 0.2 m apart. At a certain downstream location where fully-developed conditions apply, the wall shear stress is measured to be 0.027 N/m2. a. Determine the streamwise mean velocities at locations 0.25 mm and 1 cm from the wall. b. At which of these two locations do you expect to find the larger Reynolds shear stress.
Problem No-3: Air at 20 c(p-1.21kg/mH-38x107 kg.m/s) and with a free stream velocity o 40 m/s flows past a smooth thin plate which is 3-m wide and 10-m long in the flow direction. turbulent boundary layer from the leading edge determine: (a) the boundary layer thickness 6 m from the leading edge (b) the drag coefficient and drag force exerted by the fluid on the thin plate Take density 1.2 kg/m3 and kinematic viscosity as 1.49 x 10-s m'/s: (12p)...