2. The kinetic viscosity of a hydraulic oil is 110cP. The oil is flowing in a 20-mm diameter commercial steel pipe with the length of 45-m. If the velocity of oil is 4-m/s and specific gravity is...

Question

Question

Answer 1

Answer #1

(b) ,calculatinqthe Faction actor 64 Re 64 72727 C)Head tosses 23 d 6. 336013 o.39 24 h-16.14

Answer 2

Similar Homework Help Questions

A hydraulic oil with a kinematic viscosity of 4 x 10-4 m2/s and specific gravity of...

A hydraulic oil with a kinematic viscosity of 4 x 10-4 m2/s and specific gravity of 0.89 flows in a 22 mm diameter pipe at 3 m/s. Determine the head loss (in bar) due to friction for a 95 m long pipe.?
The kinematic viscosity of a hydraulic oil is 89 cS. If it is flowing at 17...

The kinematic viscosity of a hydraulic oil is 89 cS. If it is flowing at 17 ft/sec through a 2 in-diameter commercial steel pipe, what is the friction factor?
A light oil is flowing through a commercial steel pipe of diameter D1. The head available...

A light oil is flowing through a commercial steel pipe of diameter D1. The head available to produce flow is independent of the flow rate. It is decided to utilise this head to increase the oil flow rate fourfold by installing a second pipe in parallel with the first pipe and of the same length. What should the diameter of the second pipe be, if: (i) flow in each of the two pipes is highly turbulent and the same roughness...

Oilspecific gravity 0.85 and dynamic viscosity 1.52 x 103 Pa.s to flow in a 550 mm diameter uPVC ...

help me to answer question 9,11,13 please Oilspecific gravity 0.85 and dynamic viscosity 1.52 x 103 Pa.s to flow in a 550 mm diameter uPVC pipe. The allowable friction head loss is imited to 15 m and length of pipe is 100 m. al using Darcu-Weisbach formula, determine the flow velocity, the friction factor and the flow rate. using Hazen-Wiiams formula, determine the velocity and the flow rate. MoN 10 Water must flow in a straight 450 mm diameter galvanized...
LECTURE Sp 1. Oil (relative density 0.85, dynamic viscosity-4.5x10-2kg/m-s) flows through a 75 mm diameter pipe...

LECTURE Sp 1. Oil (relative density 0.85, dynamic viscosity-4.5x10-2kg/m-s) flows through a 75 mm diameter pipe with a mean velocity of 0.65 m/s. Determine i. the pressure drop in a 500 m length, ii- the friction factor, ii the head loss due to friction, iv. the maximunn velocity, and v. the velocity at 30 mm from the pipe wall. (10 marks) 46 2 9 3 8 4 5 6
5.16. Water is flowing in a 3-cm-diameter pipe at an average velocity of Uav 2 m/s....

5.16. Water is flowing in a 3-cm-diameter pipe at an average velocity of Uav 2 m/s. Assuming water density of ρ-1000 kg/m 3 and viscosity μ-10-3 N s'm2, calculate the velocity at the center of the pipe, the shear τ at the wall, and the Reynolds number. Assuming laminar flow, calculate friction coefficient C and pressure drop dp/dx.

Q5 A process fluid is flowing with a velocity of 4 m/s in a steel pipe...

Q5 A process fluid is flowing with a velocity of 4 m/s in a steel pipe having a diameter of 187 mm and a length of 1 m and maintaining the pipe surface temperature of 96.C. The fluid is entering the pipe at a temperature of 25 C and leaving with a temperature of 76C, take Prandtl number as 12. The density and viscosity of the fluid are 1210 kg/m?, 1 x10Ns/m respectively and its thermal conductivity is 5x102 w/mk....
Show your work [14 Marks] 23. Oil has a Specific gravity 0.75 is flowing through a siphon as shown in the diagram calculate the following: a) The velocity of the oil at exit (using Bernoulli'...

Show your work [14 Marks] 23. Oil has a Specific gravity 0.75 is flowing through a siphon as shown in the diagram calculate the following: a) The velocity of the oil at exit (using Bernoulli's) b) The volumetric flow rate of oil from the tank c The flow velocity in the 60 mm diameter section of the pipe d) The pressure at point B 3.0 m se-0.75 60 mm Diameter 100m 30 mm Diameter Show your work [14 Marks] 23....
Water flows through a cast iron pipe at a velocity of 4.2 m/s. The pipe is...

Water flows through a cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long and has a diameter of 150 mm. The friction factor is 0.00593. Determine the Reynolds number and head loss due to friction.

For flow in a pipe of uniform diameter D the loss in hydraulic head, h, is given by: L u2 D 2 where L is the length of the pipe, u is the average flow velocity, g is the acceleration due to gravity a...

For flow in a pipe of uniform diameter D the loss in hydraulic head, h, is given by: L u2 D 2 where L is the length of the pipe, u is the average flow velocity, g is the acceleration due to gravity and f is a constant. During reconfiguration of a plant it is estimated that the length of the pipe could be reduced by 15% and its diameter increased by 6%. Calculate the maximum percentage by which The...