please like sir
Q4) If the allowable stress is 120 MPa in tension and 150 MPa in compression, determine...
Knowing that for the extruded beam shown the allowable stress is 120 MPa in tension and 147 MPa in compression, determine the largest couple M that can be applied. The largest couple M that can be applied is 13.83 13.83 Incorrect kN·m.
The beam shown is made of a nylon for which the allowable stress is 25 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. 52 mm 21 mm 42 mm 26 mm M 278.8 N m
PROBLEM 3 Knowing that for the cantilever beam shown in Figure 3, the allowable stress is 120 MPa in tension and 150 MPa in compression, determine the largest couple M that can be applied. Figure 3 (b) Section a-a (dimension not to scale) "Х Figure 3(c) 610UB125 Figure 3(d) 300PFC dt(X10s yo section | x | y (x106 2 mm 986 72.4 610UB125 1600022961219.6 11.9 5110 90 300 16 39.3 4.04 300PFC 24.1 Figure 3 (a)Cantilever beam 300PFC 610UB125 Figure...
The beam shown is made of a nvlon for which the allowable stress is 23 MPa in tension and 31 MPa in compression. Determine the largest couple M that can be applied to the beam. 28mm- 12 mm 24 mm 14 mm N m
The beam has the triangular cross section shown. The allowable stress in bending is 150 MPa. Determine the largest allowed uniform distributed load w. 6 m 300 mm 150 mm
PROBLEM 3 Knowing that for the cantilever beam shown in Figure 3, the allowable stress is 120 MPa in tension and 150 MPa in compression, determine the largest couple M that can be applied. Figure 3 (b) Section a-a (dimension not to scale) "Х Figure 3(c) 610UB125 Figure 3(d) 300PFC dt(X10s yo section | x | y (x106 2 mm 986 72.4 610UB125 1600022961219.6 11.9 5110 90 300 16 39.3 4.04 300PFC 24.1 Figure 3 (a)Cantilever beam 300PFC 610UB125 Figure...
QUESTION 11 Knowing that for the extruded beam shown in the figure below, the allowable stress is 120 MPa in tension and 150 MPa in compression. 125 mm N-A 50 mm 125 mm 150 mm The centroid () measured from bottom of cross-section is: [mm.] 114.7 138.25 151.32 163.17 NI QUESTION 12 The moment of inertia () around neutral axis (N.A.) is: [m 122.16x 10 5 165.56x 10 5 212.45x 10 6 310.11x 10 5
6. For the cast iron link shown, the largest allowable stresses are 30 MPa in tension and 120 MPa in compression. Determine (a) the largest force P which can be applied, (b) the location of the neutral axis relative to point B. 90 mm A 20 mm P ID P' 40 mm 10 mm B B 10 mm 30 mm Section a-a
Using an allowable stress of 154 MPa, determine the largest bending moment M that can be applied to the wide-flange beam shown. Neglect the effect of fillets. (Round the final answer to one decimal place.) 12 mm 12 mm 200 mm The largest bending moment that can be applied is KN-m.
4kN 150 mm 2kN Problem 1, subjected to two concentrated forces and has a as shown in the figures The cantilever beam, (fixed at A)s 0 mm30 mm -30 mm (a) Determine the maximum shear stress on the section (b) Determine the maximum bending stress in compression and in tension (c) If the allowable bending stress (for tension and compression) is ơao.-6 MPa, calculate the new minimum required section modulus. 4kN 150 mm 2kN Problem 1, subjected to two concentrated...