width of gate into the page is 2.5m. find what the depth below the surface lf...
QUESTION 2 (10 marks) A rectangular gate of width w = 2m, and length L - Xm, and of uniform thickness so that the centre of mass is located at the centroid, holds back a depth of water at 15°C as shown. The water surface is at the same height as the gate hinge. Find the minimum weight of the gate so that the gate remains closed. 8 = 30° L=4m Water Wm
Problem 2 A concrete dam has a curved surface and restrain water (p=1000kg/m3) at a depth H=2 m. The trace of the surface is a parabola described by the equation: z= 0.2x2 . dam 1- Determine the gage pressure distribution in the water 2- Determine the magnitude of the pressure force F acting on the curved dam surface per unit width (dimension normal to the page) of the gate. [Solution: F=45,780 N] 3-Determine the angle of that force relative to...
The control gate ACB is pinned at A and rests on the smooth surface at B. The gate has a width of 5 ft. Neglect the weight of the gate. ye 62.4 lb/ft3 Figure 1) ▼ Part A If the counterweight C is 1500 lb, determine the maximum depth of water h in the reservoir before the gate begins to open Express your answer using three significant figures View Available Hint(s ft Figure < 1of1 > Submit 3 ft Provide...
In the figure below, find the force applied on the gate AB. The width of gate is 6 ft. Ignore the weight of the gate. (Note: Moment M keeps the gate closed, however, you do not need to calculate it) B 3007 TILLLLLLLLLLL M 3 PEL Water 32 S.G. 6.0
Find the torque required to hold gate closed. Tank contains water. Width of rectangular gate is 1 m. atm Surface atm 8 m gate 1 m Y. 1 m pivot
Q2/ This rectangular gate (3m high and 2m width) shown in Fig.2 below will open automatically when the depth of water (d) becomes large enough. What is the minimum depth that will cause the gate to open? d Pivot 3 mx 2 m) 1.35 m * 1.2 m
(1 point) F. The gate shown in the figure is pinned at point A and prevents liquid from escaping the fluid region. The liquid depth H 13.25 m, the gate length L 4.3 m, the gate width into the page W-9.3 m, and the gate is oriented at an angle θ 49.5° above the horizontal plane. If the liquid in the fluid region is water at a temperature of 20°C, determine the force Fr delivered by the stop. Fz MN
QUESTION 3 Figure below indicated that a plug with cone shape used to plugged a hole of 45 cm radius at one side of a tank that containing X fluid (SG-0.8). The cone is 1.5 m height and I.I m bottom diameter. Depth of cone center point to the surface liquid is 10m. a) Draw the distribution of pressure onto the plug b) Determine the force acts onto the plug Cone 10 m QUESTION 4 Figure below shows a water...
3. (Points-8) A submarine is 30.5 m below the water surface as shown in the figure below. Find the minimum force (F) required to open the circular hatch (door) when applied as shown. The tore applied perpendicular to the hatch as shown in the figure. The pressure inside the submarine is eq atmospheric pressure. Take density of water to be 1000 kg/m,-9.8 m/s and Pam - 100 kPa Water Surface atm 30.5 m circle of radius R with centroid at...
Answer should be 13450 lbf 5. (25 pts) The angled gate shown below should be designed to just begin opening when the total water depth is 6 ft. If the gate is constructed of a homogeneous material and hinged at the bottom as shown, what is the minimum weight of the gate needed to satisfy this condition? The width of the gate into the page) is 10 ft. resh water at 2 ft Gate standard conditions 60° Hinge 0