Homework Answers
Add Answer to:
ta. (25 points) Using an allowable shearing stress of 5 ksi, design a solid shaft that...
A solid 1.50-in.-diameter brass [G = 6600 ksi] shaft (2) has been stiffened between A and...
A solid 1.50-in.-diameter brass [G = 6600 ksi] shaft (2) has been stiffened between A and B by the addition of an aluminum-alloy tube (1). The tube has an outside diameter of D1 2.50 in., a wall thickness of t10.10 in., a length of L 12 in., and a shear modulus of G- 3900 ksi. The tube is attached to the brass shaft by means of rigid flanges welded to the tube and to the shaft. (The thickness of the...
sructural mechanics Q2. A solid circular shaft has to transmit a power Pat w rpm without...
sructural mechanics
Q2. A solid circular shaft has to transmit a power Pat w rpm without exceeding the shearing stress of t and angle of twist of e degree in a length of 26 times the diameter. How much should be the diameter of this shaft if the modulus of elasticity of shaft material is E and poisson's ratio is v. Assume that the material remains clastic. P=14(MW) W = 1800(rpm) T= 35 (MPa) - 2 v=0.3 E=CMPa) Page 4...
If the design of a solid shaft based on the maximum-distortion-energy leads to 6 C= (4M2...
If the design of a solid shaft based on the maximum-distortion-energy leads to 6 C= (4M2 + 3T2 + 372)) where c is the radius of the shaft, Mis the applied moment and T is the applied torque. Calculate the minimum diameter of the shaft below in in to 2 decimal places, if allow = 76 ksi. D с A B 10.5 ft 3 ft -0.5 ft 2 ft 120 lb 300 lb 300 lb 120 lb
Name: Section: Problem 24 A solid circular shaft is used to transmit 10 hp while rotating...
Name: Section: Problem 24 A solid circular shaft is used to transmit 10 hp while rotating at 3,300 rpm. Design the diameter of the shaft to the nearest 1/8” if the maximum allowable shear stress in the shaft is 1500 psi. a) 1/4 in. b) 1/2 in. c) 5/8 in. d) 7/8 in. e) 1 in. o o o o ооо
sel engine for a commercial boat operates at 200 rpm and delivers 800 hp through a...
sel engine for a commercial boat operates at 200 rpm and delivers 800 hp through a 1) A die with a ratio of 4 to 1 to the propeller as shown below. Because the propeller shaft gearbox ed is four times that of the crank shaft, the torque on the propeller shaft is one-fourth that spe o the crank shaft. Both the shaft from the engine to the gearbox and the propeller shaft are to be solid and made of...
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a...
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 3600 lb-in. The shaft is made out of aluminum. Aluminum Shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. 02:55:27 Allow Shear Stress (ksi) Allow Angle of Density Cost per Modulus of Pound Rigidity ($) (ksi) Twist (deg.) Kib/A3)...
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is...
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...
Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque...
Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 4800 lb-in. The shaft is made out of aluminum. Aluminum shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. Cost per Allow Shear Stress kksi) Allow Angle Density of Twist (deg.) (1/A3) Pound Modulus of Rigidity (ksi) Aluminum 18 4.5...
In the system of shaft and gears below, T_c=45 kip.in., Calculate the maximum shearing stress in shaft BC if it is made out of hollow cylinder shown below. Using relations between system of gears predict TF Design solid Shafts EF if ultimate sharing
In the system of shaft and gears below, a) Calculate the maximum shearing stress in shaft BC if it is made out of hollow cylinderb) shown below.c) Using relations between system of gears predict TFd) Design solid Shafts EF if ultimate sharing stress is 9000 psi, use F.S=1.75
Show step for step please! Shaft Design: Part.1 (60 pts) Consider the shaft system in Fig.1. The shaft is to be made of high-carbon steel (out 89.2 ksi , σ 55.2 kst) for infinite life. Standard b...
Show step for step please!
Shaft Design: Part.1 (60 pts) Consider the shaft system in Fig.1. The shaft is to be made of high-carbon steel (out 89.2 ksi , σ 55.2 kst) for infinite life. Standard ball bearings support the shaft at z 0 and z -54 in and do 0.75 d The applied loads are steady such that bending moments are completely rev 2.5 hp of horse power, where (1 hp = 550 lb . in/s) is transmitted to)the...
A solid 1.50-in.-diameter brass [G = 6600 ksi] shaft (2) has been stiffened between A and B by the addition of an aluminum-alloy tube (1). The tube has an outside diameter of D1 2.50 in., a wall thickness of t10.10 in., a length of L 12 in., and a shear modulus of G- 3900 ksi. The tube is attached to the brass shaft by means of rigid flanges welded to the tube and to the shaft. (The thickness of the...
sructural mechanics
Q2. A solid circular shaft has to transmit a power Pat w rpm without exceeding the shearing stress of t and angle of twist of e degree in a length of 26 times the diameter. How much should be the diameter of this shaft if the modulus of elasticity of shaft material is E and poisson's ratio is v. Assume that the material remains clastic. P=14(MW) W = 1800(rpm) T= 35 (MPa) - 2 v=0.3 E=CMPa) Page 4...
If the design of a solid shaft based on the maximum-distortion-energy leads to 6 C= (4M2 + 3T2 + 372)) where c is the radius of the shaft, Mis the applied moment and T is the applied torque. Calculate the minimum diameter of the shaft below in in to 2 decimal places, if allow = 76 ksi. D с A B 10.5 ft 3 ft -0.5 ft 2 ft 120 lb 300 lb 300 lb 120 lb
Name: Section: Problem 24 A solid circular shaft is used to transmit 10 hp while rotating at 3,300 rpm. Design the diameter of the shaft to the nearest 1/8” if the maximum allowable shear stress in the shaft is 1500 psi. a) 1/4 in. b) 1/2 in. c) 5/8 in. d) 7/8 in. e) 1 in. o o o o ооо
sel engine for a commercial boat operates at 200 rpm and delivers 800 hp through a 1) A die with a ratio of 4 to 1 to the propeller as shown below. Because the propeller shaft gearbox ed is four times that of the crank shaft, the torque on the propeller shaft is one-fourth that spe o the crank shaft. Both the shaft from the engine to the gearbox and the propeller shaft are to be solid and made of...
5 Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 3600 lb-in. The shaft is made out of aluminum. Aluminum Shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. 02:55:27 Allow Shear Stress (ksi) Allow Angle of Density Cost per Modulus of Pound Rigidity ($) (ksi) Twist (deg.) Kib/A3)...
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...
Section 2 Problem 5 (25 pts.) A solid shaft 32 inches long must carry a torque of 4800 lb-in. The shaft is made out of aluminum. Aluminum shafts come in increments of 1/16th inch increments between diameter of 0.25 and 2.5 inches. Determine: a) the required size and cost of an aluminum shaft based on the below design criteria. Cost per Allow Shear Stress kksi) Allow Angle Density of Twist (deg.) (1/A3) Pound Modulus of Rigidity (ksi) Aluminum 18 4.5...
In the system of shaft and gears below, a) Calculate the maximum shearing stress in shaft BC if it is made out of hollow cylinderb) shown below.c) Using relations between system of gears predict TFd) Design solid Shafts EF if ultimate sharing stress is 9000 psi, use F.S=1.75
Show step for step please!
Shaft Design: Part.1 (60 pts) Consider the shaft system in Fig.1. The shaft is to be made of high-carbon steel (out 89.2 ksi , σ 55.2 kst) for infinite life. Standard ball bearings support the shaft at z 0 and z -54 in and do 0.75 d The applied loads are steady such that bending moments are completely rev 2.5 hp of horse power, where (1 hp = 550 lb . in/s) is transmitted to)the...
Most questions answered within 3 hours.
-
For the reaction system: H2 (g) + CO2 (g) → H2O (g) + CO (g)
The...
asked 3 minutes ago -
In a random sample of 100 homes in a certain city, it is found
that 10...
asked 11 minutes ago -
A compression ignition engine is being analyzed. The
residual gas fraction is xr=0.02. The fuel-to-air
equivalence ratio is...
asked 21 minutes ago -
Which of the following is FALSE about Slow Twitch Fibers (Slow
fibers, slow oxidative fibers) compared...
asked 25 minutes ago -
Need help with drawing the mechanism of succinic anhydride to
succinimide via ammonia and heat. Kind...
asked 44 minutes ago -
Steve is a sales rep for Clearwater Purification Systems, a
national manufacturer of residential water treatment...
asked 29 minutes ago -
Question 4. Using your knowledge of IS-LM, solve the following:
8
12
1+r 1+r
(a) If...
asked 34 minutes ago -
Paige's Properties Inc. reported 2018 net income of $2.90
million and depreciation of $269,000. Paige's Properties,...
asked 43 minutes ago -
Using loops, write a C# program that asks the user to
enter repeatedly an integer number,...
asked 49 minutes ago -
A researcher conducts an experiment comparing three treatment
conditions. The data consist of n = 34...
asked 1 hour ago -
A generating station is producing 1.8 x 106 W of power that is
to be sent...
asked 58 minutes ago -
Consider the reaction Mg(s)+Fe2+(aq)→Mg2+(aq)+Fe(s) at 49 ∘C ,
where [Fe2+]= 3.30 M and [Mg2+]= 0.210 M...
asked 59 minutes ago