A pair of helical-tooth cylindrical gears transmits 2 kW with an input rotation of 1720 rpm; it is known:
Bending strength of gear steel = 90 MPa
HB = 2300 N / mm 2
Pressure angle = 20o.
Number of teeth z1 = 17 z2 = 65
Propeller angle equal to 30o.
Gear width = 63 mm
Determine the normal modulus of the pair.
a) 2.5mm
b)3.5mm
c)4.5mm
d)5.5mm
e)6.5mm
A pair of helical-tooth cylindrical gears transmits 2 kW with an input rotation of 1720 rpm;...
Figure Q1 shows a gear train consists of four spur gears A, B, C and D to be designed for a specific mechanism. The power transmitted by gear A is 5 kW at rotational speed of 720 rpm counterclockwise direction. Number of teeth (N) for gears A,B,C and D are respectively 20, 50, 30 and 60. The module and pressure angle of the gears are respectively 4 mm and 20o . Determine followings: (a) Tangential and radial forces between gears...
A step down gear drive is used in a conveyor system. The input pinion is made of 18 teeth runs at 1720 rpm, the driven gear runs at 860 rpm. The gears are supported on less rigid mountings, less accurate gears. The gears are made by hobbing process. Find: (a) The tooth bending strength of both wheels and the maximum power that can be transmitted to the drive (b) By considering surface durability conditions find the_maximum power that can be...
The Isthmus Slough drawbridge has an open gear reduction for the span drive. A mating pair of gears pinion E and gear Fare located about mid-way in the 5 part speed reduction. The gear teeth are un- crowned open spur gears with a pressure angle o = 20 degrees. Both gears are made to an AGMA quality level Qv = 9 and have a measured hardness of HB = 183 made from through hardened Grade 1 Steel and are un-lapped....
output input 2. The gearbox in the diagram for problem 1 receives an input power of 10 kW, at a speed of 40. The gears are spur gears (ignore the helix angle on the teeth in the figure), have a module of 5 mm/tooth, and the pressure angle is 20. Assume all shafts lie in the same plane. Assume the gearbox is reasonably efficient, so losses can be neglected for this analysis. (a) Determine the minimum inside dimension of the...
A pair of bevel gears is required to transmit 11 kW at 500 r.p.m. from the motor shaft to another shaft, the speed reduction being 3 : 1. The shafts are inclined at 60º. The pinion is to have 24 teeth with a pressure angle of 20º and is to be made of cast steel having a static stress of 80 MPa. The gear is to be made of cast iron with a static stress of 55 MPa. The tooth...
A pair of straight bevel gears are mounted on shafts that are 90 degrees apart, and pinion transmits 10 hp at 300 rpm. The pinion has 6" outside pitch diameter, 2" face width, 20 teeth and Φ = 20˚. For a velocity ratio of 0.5, draw a free body diagram of gears showing all forces. What is torque produced about gear axis? The average pinion pitch diameter is 5.104"
6.6 A 20° full depth spur pinion is required to transmit 1.8 kW at a speed of 1100 rpm. If the pinion has 18 teeth and is manufactured from heavy duty 817M40 steel select a suit- able gear from the limited choice given in Lewis formula, if the bending stress should not exceed 75 MPa. width 20 mm L able 6.8 Spur gears: 15 module, heavy duty steel 817M40, 655SM13, face w Bore Outer Boss PCD d number Teeth (mm)...