Consider an LTI system with the impulse response h(t) = e- . Is the system casual?...
CONVOLUTION - Questions 4 and 5 4. Consider an LTI system with an impulse response h(n) = [1 2 1] for 0 <n<2. If the input to the system is x(n) = u(n)-un-2) where u(n) is the unit-step, calculate the output of the system y(n) analytically. Check your answer using the "conv" function in MATLAB. 5. Consider an LTI system with an impulse response h(n) = u(n) where u(n) is the unit-step. (a) If the input to the system is...
Consider the LTI system with input ??(??) = ?? ?????(??) and the
impulse response ?(??) = ?? ?2????(??). A. (3 points) Determine
??(??) and ??(??) and the ROCs B. (3 points) Using the
convolutional property of the Laplace transform, determine ??(??),
the Laplace transform of the output, ??(??) C. (3 points) From the
answer of part B, find ??(??)
9 points) Consider the LTI system with input x(t)eu(t) and the impulse response h(t)-e-2u(t) A. 3 points) Determine X(s) and H(s)...
(1) For the impulse response (h(t)) and input signal (x(t)) of an LTI system shown below, find and plot the output response (y(t)) by integrating the convolution analytically h(t) x(t) t (s)
Q1) Consider an LTI system with frequency response (u) given by (a) Find the impulse response h(0) for this system. [Hint: In case of polynomial over pohnomial frequency domain representation, we analyce the denominator and use partial fraction expansion to write H() in the form Then we notice that each of these fraction terms is the Fourier of an exponentiol multiplied by a unit step as per the Table J (b) What is the output y(t) from the system if...
3-(10 points) Consider a C-T. LTI system given below X(t) - h(t) y(t) The impulse response is h(t)=sinc(200t). We apply an input signal x(t)=sinc(100t) to produce the output y(t). Find and plot Y(m). Find y(t).
Given a zero-state LTI system whose impulse response h(t) = u(t) u(t-2), if the input of the system is r(t), find the system equation which relates the input to the output y(t) 4. (20 points) If a causal signal's s-domain representation is given as X (s) = (s+ 2)(s2 +2s + 5) (a) find all the poles and zero of the function. 2 1 52243 orr
Consider the LTI system described by the following impulse response: (a) h(n) = 2(0.5)n u(n). Determine: (i) The system function representation; (ii) the difference-equation representation (Note: this is just terminology that refers to expressing the input and output time-domain signals in the form of an equation. E.g., what we did when we went over the equations for block diagrams); (iii) The pole-zero plot, sketched by hand; and (iv) the output y(n) if the input is x(n) = (0.25)n u(n) [10...
The unit impulse response and the input to an LTI system are given by: h(t) u(t) - u(t - 4) x(t) e2[u(t)-u(t - 4)] x(t) 1 y(t) h(t) 1. Determine the output signal, i.e.y(t), you may use any method. 2. Is this system memoryless? Why? 3. Is this system causal? Why? 4. Is this system BIBO stable? Why?
1. (20 p) Compute and sketch the output y(t) of the continuous-time LTI system with impulse response h(t) = el-tuſt - 1)for an input signal x(t) = u(t) - ut - 3). 2. (20p) Consider an input x[n] and an unit impulse response h[n] given by n-2 x[n] = (4)”- u[n – 2] h[n] = u(n + 2] Determine and plot the output y[n] = x[n] *h[n].
2.7.5 The impulse response of a continuous-time LTI system is given by h(t) = f(t) - et u(t). (a) What is the frequency response H (w) of this system? (b) Find and sketch H(w). (c) Is this a lowpass, bandpass, or highpass filter, or none of those? 2.7.6 The impulse response of a continuous-time LTI system is given by h(t) = S(t – 2). (This is a delay of 2.) (a) What is the frequency response H (w) of this...