bia Ro R, MO Mi 1. Specifications. (b) The DC voltages at Vntli and Vwir are...
3. In Figure 3 on page 5, the DC operating point for the PNP transistor Qi is Ic = 0.33 mA and Vec = 2.4 V, and the DC operating point for the NMOS transistor Mi is ID = 2.81 mA and Vos = 2.92 V. Qı has B = 100, VA = 85 V at room temperature and Mi has Kn= 1 mA/V2, Vin= 1 V and 2 = 0.02 V-1. Assume that the capacitors have infinite values, and...
1.) 120 pointsl The parameters of n-channel enhancement MOSFET in the amplifier circuit below are: 2.042 mA/V2, 1 Val ½ 2.4 V, Kn 150 V a.) Find quiescent values: drain current i, gate-to-source voltage vGs, and drain-to-source voltage vDs b.) Determine AC model parameters: gm and ro c.) Determine amplifier model parameters: Ri, Ro and Avo d) Determine the output voltage Vl across the load RL ǐfv, 1 mYn +VDD GI〈 R ls R Mi RL 1.) 120 pointsl The...
QUESTION (1) Transistor Mi in this common base amplifier circuit has the following characteristics: +Vc VTH =1 V Rp R, C. K 1 mA/V2 2 0.1 R Given: Vcc 2 mA, 10 V, lbias Ct C2 0, 5 k2, RD 2 k2 RI 10 k, R2 R (12 points) a) Determine the small signal gain, vo/Vin. (4 points) b) Determine the input resistance, Rin. (4 points) c) Determine the output resistance, Ro. Useful formulae: for n-channel MOSFET triode region =...
V.+w Operation in the triode reglon Condition v. e Wov 20 Vos uov os os-V (2) p V, so onl+Pala Characteristics Same relationships as for NMOS trasistos tCharacteristics: a CuGs- V,) ®os- } ip.C Replace .and NA with p,,and Nprespectively. V.V V, and yare negative. 2 wov ps For vos 2( -V) e Conditions for operation in the triode region ip lvi Q1. (10 points) For the following configuration of the given figure below, with the following parameters: VDD= +10...
Rpi Ri Mi 1. Specifications (a) RR21 150 k. (b) RDi 3 k2. (c) Rs1 400 Ω. (d) RL 10 k. (e) 9m-10 mS. (f) Use 10μF capacitors. (h) Cod 5 pF (i) Cds= 25 pF Tasks (a) Determine (b) Determine Tod (c) Determine TL from Ci2 and CDB) (d) Determine H, the 3 dB high frequency bandwidth Rpi Ri Mi 1. Specifications (a) RR21 150 k. (b) RDi 3 k2. (c) Rs1 400 Ω. (d) RL 10 k. (e)...
Answer A & B & C as fast as u can 1. The amplifie parameters for each transistor and circuit components are given in the figure, 100 for both Q1 and Q2, and VeEVEe 0.7V. VA 200V for Q1, and VAo for r of the following figure consists of two CE amplifiers connected in cascade. The consider the β and capacitor is very large. (120 pts) RI V. Q2 -4V culate corresponding DC currents (U-) and DC voltages (V-Vs) through...
Lab Preparation . Using DC analysis, and assuming that the transistors (QuEr and Q) are in the active mode, determine the value of RREF required for generating a copy current of 0.755 mA. Take the value of Vcc to be 8 V, and the value of VE in the active mode to be equal to 0.7V. Vee H Qur о RaI Figure 3 Single-stage amplifier biased by a simple current miror device 2. The circuit shown in Figure 3, is...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...