You are using a wrench in an attempt to loosen a nut by applying a force as shown; but this fails to loosen the nut. Which one of the following choices is most likely to loosen this tough nut? Select all that apply.
Doubling the length or doubling the force will have the same result, but doubling the length is easier.
Continue applying the same force as in the drawing and eventually the nut will loosen.
Place a pipe of length 2L over the handle of the wrench and apply the same force F to the opposite end(farthest from the nut).
Tie a rope of length 2L to the wrench at the same location and apply the same force as shown.
Double the force.
You are using a wrench in an attempt to loosen a nut by applying a force...
QUESTION 1 A wrench is used to loosen a nut as shown below by applying a force 13 N. Determine the torque (magnitude and direction:+for CCW and for CW) about the nut joint Express your answer in Sl units with 3 or more significant figures 0.28 m QUESTION 2 The drawing shows a person mass 59 kg. doing push-ups. Find the force exerted by the floor on each foot assuming that the person holds this position Express your answer in...
Rotational Dynamics 1. You are using a wrench and trying to loosen a rusty nut. Which of the arrangements shown is most effective in loosening the nut? List in order of descending efficiency the following arrangements:
Madison uses a 35.0 cm long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30.0o above the horizontal as shown in the figure, and Madison pulls straight down on the end with a force F = 210 N. How much torque (N m) does Madison exert on the nut? Enter just the numerical value of the answer in Newton-meters, without entering the units. Enter your answer to three significant figures, and remember to include the...
If I am applying a torque to a wrench such that the angle between the force applied and the wrench is 30 degrees, how much more torque could I apply if I was pushing with the same amount of force but at 90 degrees to the wrench?
HW05 roblem 4.53 The lug nut on the wheel of the automobile is to be removed using the wrench. The cheater pipe AB is slipped over the handle of the wrench and a force of F-31 N can bo applied at any point and in any direction on the assembly. (Figure 1) Previous Answers Correct Part C gure 1 of 1 Dotermine the greatest possible magnitude of the moment of the force about the z axis Express your answer to...
part c=d How much force must you and your friend each apply to the free end of the door on the same side and perpendicular to the plane of the door in order to produce the same torque as that produced by both of you in part (a) above? N (d) What is the angular acceleration of the door? rad/s2 A heavy swing door has a mass of m = 7,500 kg, a width W = 1.9 m, and a...
please answer all pre-lab questions 1 through 5. THANK YOU!!! this is the manual to give you some background. the pre-lab questions.. the pre-lab sheet. Lab Manual Lab 10: String Waves & Resonance Before the lab, read the theory in Sections 1-3 and answer questions on Pre-lab Submit your Pre-lab at the beginning of the lab. During the lab, read Section 4 and follow the procedure to do the experiment. You will record data sets, perform analyses, answer questions, and...
please answer all prelab questions, 1-4. This is the prelab manual, just in case you need background information to answer the questions. The prelab questions are in the 3rd photo. this where we put in the answers, just to give you an idea. Lab Manual Lab 9: Simple Harmonic Oscillation Before the lab, read the theory in Sections 1-3 and answer questions on Pre-lab Submit your Pre-lab at the beginning of the lab. During the lab, read Section 4 and...
pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC worksheet t hree Copper conductors with THHN insulation run in Electrical A branch-circuit Consther conductors. The conductor terminations are rated for a maximum ure in the area of this installation is not expected to exceed 30C size 8 AWG, the maximum ampacity of the conductors If the conductors for this circuit are permitted A 40 amperes. B. 50 amperes. to be used...
I need help to write a nice introduction for experiment 6 please ( no hands write ) typing Thank you HEAT TREATMENT OF STEELS EXPERIMENT 6 EXPERIMENT 6 HEAT TREATMENT OF STEELS THEORY The Effect of Cooling Rate One of the most convenient methods for controlling the properties of a given steel, i.e., a steel whose composition is already fixed, consists of austenizing the steel and ten cooling to room temperature at some predetermined rate. A variation of cooling rates...