The answer is D) Please explain why. 1. Vi(t) = 1V + 0.1V sin(t/(100RC)). Choose the...

Question

Question

1. Vi(t) = 1V + 0.1V sin(t/(100RC)). Choose the best answer for Vo. O + CV OI a) V.(t) = 0.1V sin(t/(100RC)-90) b) V.(t) = 1V

The answer is D)

Please explain why.

Answer 1

Answer #1

Vilt) = lut olusin [to sec] Considen IV sounce Alone :- It is a sc source. so fcort 27x0 = oradfoec. Capacitive Reactance xc

Answer 2

Similar Homework Help Questions

2. In the circuit below all resistors are 1-ohm and the value of the inductor is 1H a. Determine the transfer function 'e in the frequency domain. b. If Vi(t) = 3 n= 1-sin (nrt) determine vo(t) c...

2. In the circuit below all resistors are 1-ohm and the value of the inductor is 1H a. Determine the transfer function 'e in the frequency domain. b. If Vi(t) = 3 n= 1-sin (nrt) determine vo(t) c. Determine the input normalized power 1 나 1 V. 2. In the circuit below all resistors are 1-ohm and the value of the inductor is 1H a. Determine the transfer function 'e in the frequency domain. b. If Vi(t) = 3 n=...
Please explain why is the answer D? B: 0.5 A, 120 Ω D' 2.0 A, I...

Please explain why is the answer D? B: 0.5 A, 120 Ω D' 2.0 A, I 20 Ω bulb marked 12 V, 24 W is connected in f different ways as in the circuits below. In wh |/ 90. abelled ‘720 W, 240 V". f the heating filament and e kettle? ich norma --way is the bulb is going to glow with brightness when connected to a 36 V su pply? Current/A 0.3 3.0 0.3 6Ω 36V 623 (C 3.0...
a)Which LED will be turned on when vi = 1V? Which LED will be turned on...

a)Which LED will be turned on when vi = 1V? Which LED will be turned on when vi=-1V? b) Write an equation for v1 as a function of the pot setting ?. Assume ? = 0 corresponds to the slider being all the way up. c) What do you expect the LEDs to do for a pot setting of ? = 0.4? How about ? = 0.5? How about ? = 0.6? d) What is the threshold ? for the Schmitt trigger...

For all BJTs, assume: IVBE,on1-0.7V, β 100, and|VCE,sat-0.1V (use Vr 25mV) For all MOSFETs, assume: I'm|-1V...

For all BJTs, assume: IVBE,on1-0.7V, β 100, and|VCE,sat-0.1V (use Vr 25mV) For all MOSFETs, assume: I'm|-1V and μ COX-20 V2. Q3: Consider the circuit shown to the right where W- 100. Resistor values are: RG 1M, RD 10kn, Rs 500, R 20k0, and Rs 100k. The capacitors should be assumed short- circuits at the operating frequency of the circuit and Vo -Vss = +3V. a) Calculate the bias point parameters (lo and Vos) for the Rai Ca Rsi transistor and...
Choose the correct answer and explain why you choose that answer. -Page 2 4. The Claisen...

Choose the correct answer and explain why you choose that answer. -Page 2 4. The Claisen condensation produces which of these? a- An α-keto ester b.AB-keto ester C, A β-hydroxy ester d. A B-hydroxyaldehyde e. A B-di ketone 5. Which compound could be prepared using a Michael reaction? 0 0 o 1 CCH3 СОС2HS a. I d. IV e. v Part 2 t. The product (s) of the reaction of 2 mol of ethyl butanoate sodium ethoxide is(are) : b....
Find v, in the given circuit where P = 90 sin(2t) V. Please report your answer...

Find v, in the given circuit where P = 90 sin(2t) V. Please report your answer so the magnitude is positive and all angles are in the range of negative 180 degrees to positive 180 degrees. 0.5 H + P 2H ele ell 2 H vo 0.5 F The value of vo(t) = cos(2t+ 1) v.

The answer is B. Please show why. 4. Let Vcc 5 and find vo. a) 1...

The answer is B. Please show why. 4. Let Vcc 5 and find vo. a) 1 V b)-2 V c) 3 V d)-4V e) none of these 1 0
can please explain why F(sigma)= u? We consider the PDE: for given o(t) € H|(12) find...

can please explain why F(sigma)= u? We consider the PDE: for given o(t) € H|(12) find the (weak) solution u € H}(2) of V. (g(x)Vu(x)) = 1. The corresponding parameter-to-solution map is defined as F: D(F):= H (1) C H²(2) L’(1) F(o)= u uc H (12) c L’(2) solving b(u, w;o) = f(w) for all w e H7(), b(u, w; 0) := ( D2.Vwdi, f(w):=- / w dr. The associated inverse problem is for u E L(12) find o E...
Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly....

Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly. Why is the answer A? Please explain clearly....

Explain using theory, why does the simulation result is shown as followed Summing Amplifier

Explain using theory, why does the simulation result is shown as followed Summing Amplifier Rf Ra Rb Vo VcM Simulation condition Transient simulation (Vo vs Va,b,c) Amplitude 0.1V offsetV Frequency-1KHz Amplitude 0.05V -5V offset 5 Frequency 2KHz Amplitude 0.1V/0.2V/0.3V offset5 V Frequency 1KHz U1 R1 6 OU 20k R3 2 UA741 20k R4 R2 20k 47K V4 V5 V6 V1 cFREQ ~) VAMPL = 0 FREQ = 2k VAMPL = FREQ = 1k AC=1 GND PARAMETERS We were unable to...