4) For a Given Operational Amplifier Please Determine the following Quantities, Amid Voltage Gain 450 f1...
a The operational amplifier in Figure 3.a has a slew rate of 0.5V/us and a unity gain bandwid of 5 MHz. Determine () the voltage gain, and (ii) the maximum input frequency such that the output waveform is undistorted. with Vpeak 1V and frequency f. () Determine the cutoff frequency, (ii) plot, to scale, the you use this integrator if the input frequency is 30 KHz? Explain your answer. that any feedback resistance is fixed to 5k2. b. In the...
Express the voltage gain 15.8, current gain 4.43 x 104, and power gain 10 x 10 in dB. AvdB = Аав в ApdB - The amplifier in the given figure has R, -8.1k0, R = 140 kO and operates from 112. V power supplies OVO References eBook & Resources Section Break Difficulty: Medium Learning Objective: Find op amp circuit 2. value 10.00 points What is the voltage gain Ay Volvof the circuit? (Round off the solution to one decimal place.)...
please make sure you are correct 1. Select configuration for a single-transistor amplifier with a gain of 30 dB and input resistance of 5 Mohm. A) common-emitter; b) common-gate; c) common-source; d)common-collector; e) cannot be implemented by single stage amplifier. 2. Select configuration for a single-transistor amplifier with a gain close to 0 dB and input resistance of 5 Mohm and load resistor of 50 ohm. a) common-emitter; b) common-gate; c) common-source; d)common-collector; e) cannot be implemented by single stage...
4. Design a npn BJT C-E amplifier circuit for the following specifications and given values: Voltage Gain Input resistance Load resistance Supply voltage Av = -60 Ri = 5k92 RL = 6k2 Vcc= 16V Assume Re is fully bypassed. The input source internal resistance Rs = 0.12. B=120 and VBE= 0.65V. Draw the actual circuit and its ac equivalent circuit
1. If the voltage gain is 2000, the decibel voltage gain is a. 40 dB c. 66 dB b. 46 dB d. 86 dB 2. The input power to a device is 10.000 W. The output power is 500 W. The power gain (GdB) in decibels is a. -13 dB b. -26 dB c. 56 dB d. 18 dB 3. Which of the following is an advantage of using dB representations of gain values? (a) Positive and negative dB values...
Design an amplifier that meets the following conditions. Determine the R3 value to get the maximum voltage gain A. Find the W / L of VG, VS, VD and MOS. B. Find RD, R1, R2, R3. C. If the input frequency is 20 Hz. obtain the conditions and values that determine the Cl and C2 values V20=2.4IV].Pc =2.5m),4 = = 4\uA] 4C-100.A/,,0.SV), A= 0,e = 0,7 V ON - 51v/v)},R = 50[Q] R, >> 1/g.m Vi C=F] Design an amplifier...
Problem Consider a voltage amplifier having a frequency response of the low-pass STC 1ype with a de gain of 60 dB and a 3-dB frequency of 1000 Hz Find the gain in dB at f- 10 Hz, 10kHz, 100 kHz, and 1 MHz Problem For the circuit shown below first, evalusteand the coresponding comer froquency. Second evalmt and the corresponding comer froquency. At the end caloulate overall transfer function T(w)= and reurite it in the standard fom ( and draw...
We design a voltage amplifier using a BJT following the plan laid down in the handout "Notes on common emitter transistor amplifier 8 IN RB Design an amplifier with a Gain VoutVinl30 Assume the transistor gain is B 100. Let Vcc 15 V Choose VCE Vcc-VCE.Sat Choose Ic.o-10 mA. 1. Determine values of resistors Rc, RE, and RB so that the gain is essentially independent of the value of β 2. State and satisfy the load-line relation between lc.a and...
Please answer clearly Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a) Voltage gain (Vo/vi) b) Input resistance (R) c) Output resistance (Ro) d) Maximum output voltage swing so as the amplifier stays in saturation mode. Assume VDD-20 V, R1-2.5 ΚΩ, R2-1KQ, R3-0.5 ΚΩ, R4-5 MQ, R5_1ΜΩ. R4 R1 R5 R2 Ro R3 Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a)...
The following Amplifier needs to be designed such that the voltage gain Av = 54. Assume Vcc=10V, B=50, RL= 10 kq, RS = 100, and design for Ico= 0.48 mA and VEQ = 2V. (a) Find the values of Gm and it (b) Find the values of resistors R1, R2, RC, RE using the design procedure presented in class notes (or textbook) In the answer box write the value of Rc in ko (c) Find the Input resistance (d) Find...