15 pts Question 24 TCO 3) For the circuit below, if Vin is -5VDC, find: 10...
7 pts Question 5 (TCO 2) For the circuit below, if Vcc is 20 volts and Rb is 4.3k ohms, find the base and collector 300, the motor resistance is 100 ohms. voltages and currents for an input of OV and 5V. Beta Vcc ant Vin -n Vout Rb 1a: Whan Vin- OV. find: ть Ic = Vhase 1b: When Vin 5V. find: Ib Ic = vbase Vcol HINIL Edilotia A TE U A- B I Paragraph T 12p ED...
TCO 2) For the circuit below, if Vcc is 28 volts and Rb is 4.7k ohms, find the base and collector voltages and currents for an input of OV and 5V. Beta 300, the motor resistance is 400 ohms. AG1 NI MOTOR SERVO Vin N Yout Rb 1a: When Vin OV, find: lb = Ic = Vbase Vcol 1b: when Vin 5V, find: IC Vbase HTML Editor Question 6 7 pts TCO 1) Find the following for an input of...
10 pts Question 15 (TCO 6) How many select lines are required for a 1-to-32 multiplexer? Explain how you determined your answer HTML Editor Paragraph
3. For the circuit below, use Vin (3.0 V) (0.3 V) sin(). Find Vout 15 V out RE 0.3 kΩ
Question 3 25 pts Given the circuit below, determine the apparent power supplied by the circuit. Give your answer as positive and in units of VA. Use the following quantities: w=851 rad/sec and Vin = 14 20°V 20 mH Vout(t) Vin(t) 4 mF 292
Question 8 26 pts (TCO 3,4 & 6) Identify and give examples of three of the gender gaps that need to be narrowed B I : I = X J A O A N = = H+ = = = T12p HTML Editor = = - Paragraph - O words No new data to save Last checked at 918am Submit ou 00 e 9
5 pts Question 11 (TCO 2) A constellation diagram has two points located at (2,0) and (3,0) on the I(in- phase)-Q(quadrature phase) plane. Find the value of peak amplitude and the type of modulation this diagram represents. HTML Editor Parag 5 pts Question 11 (TCO 2) A constellation diagram has two points located at (2,0) and (3,0) on the I(in- phase)-Q(quadrature phase) plane. Find the value of peak amplitude and the type of modulation this diagram represents. HTML Editor Parag
Question 3 3 pts Focus on Op-amp U1 (Both op-amps have to be completely connected as shown in Figure A) Use myDAQ's oscilloscope to capture the input waveform Vin (on Channel 0) and the intermediate output waveform Vout1 (on Channel 1) superimposed. Set the amplitude scale for both channels of the oscilloscope to 500 mV/Div Set the time scale of the oscilloscope to 200 us/Div 1. Take a screenshot of the oscilloscope (both waveform in the same picture) and embed...
O Modules S Agile Product Life y erse... ROADP $ Nevlersey local N. G Google a Northersey Nev. Pages. Welcome. me t Question 3 6 pts (TCO 1) Find the following for an input of 120 VAC(RMS), 60 hertz, given a 15:1 stepdown transformer and a full-wave bridge rectifier. Rload is 82 ohms. Round off to the nearest tenth place. 1a: Primary or input peak voltage - 1b: Secondary peak voltage - 1c: Peak voltage out of the rectifien id:...
#24 and #25 please and thank you 24. (3 pts) Draw below a circuit to create an automatic power-on reset for digital Elip-flops, be sure to label signal names on schematic, (hint: think RC-time- constant) 25. (3 pts) Find va, Vb and Ib for the circuit shown below 5 V 10 k2 4.7 kΩ