Exit D Question 6 5 pts A gas turbine generating set is fitted with an exhaust...
1. A combined gas-steam power cycle uses a single gas turbine cycle for the air cycle and a simple Rankine cycle for the water vapor cycle. Atmospheric air enters the compressor at a rate of 88.2 lbm / s, at 14.7 psia and 59 ° F, and the maximum gas cycle temperature is 1,742 ° F. The pressure ratio in the compressor is 7. The isentropic efficiency of both the compressor and the turbine is 80%. Gas exits the heat...
Question A.1 A schematic of a gas turbine combined cycle generating plant is shown in Figure A1.1 on the next page. Exhaust gas from the gas turbine generator pass througha heat recovery steam generator (HRSG) which generates steam to drive a steam turbine generator. The following data is provided for the plant: Gas turbine 18.9:1 Pressure ratio Compressor air inlet temperature Turbine inlet temperature 15°C t 273 288 1350°C +273- 1623 588 kg/s T, T3 Exhaust gas mass flow Isentropic...
A combined cycle gas turbine/vapor power plant uses the turbine exhaust as the energy source for the boiler. Each power system uses a single turbine. The gas power system is modeled as an ideal air-standard Brayton cycle. The vapor power system is modeled as an ideal Rankine cycle. Given specific operating conditions determine the temperature and pressure at each state, the rate of heat transfer in the boiler, the power output of each turbine, and the overall efficiency. --Given Values--...
A combined cycle gas turbine / vapor power plant uses the turbine exhaust as the energy source for the boiler. Each power system uses a single turbine. The gas power system is modeled as an ideal air-standard Brayton cycle. The vapor power system is modeled as an ideal Rankine cycle. Given specific operating conditions determine the temperature and pressure at each state, the rate of heat transfer in the boiler, the power output of each turbine, and the overall efficiency....
Heat exchanger 5 Comb. Compressor Turbine A gas turbine for an automobile is designed with a regenerator. Air enters the compressor of this engine at 100 kPa and 20°C. The compressor pressure ratio is 7.8; the maximum cycle temperature is 865°C; and the cold air stream leaves the regenerator 10°C cooler than the hot air stream at the inlet of the regenerator. Assuming both the compressor and the turbine to be isentropic, determine the rates of heat addition and rejection...
In a combustion turbine using natural gas as the fuel, air enters the compressor at 98 kPa and 300 "K. The pressure ratio in the compressor is 8 and the isentropic efficiency of the compressor is 85%. The outlet temperature of the combustion chamber is 1200 K. The pressure drops by 4 percent in the combustion chamber. The exit pressure of the turbine is 102 kPa and the isentropic efficiency of the turbine is 90%. Find: a) The exit temperature...
Consider the combined gas-steam power cycle,The topping cycle is a gas-turbine cycle that has a pressure ratio of 8.Air enters the compressor at 300K and the turbine at 1300K.The isentropic efficiency of the compressor is 80 percent, and that of the gas is 85 percent.The bottoming cycle is a simple ideal Rankine cycle operating between the pressures limits of 7 MPa and 5 KPa.Steam is heated in a heat exchanger by the exahust gases to a temperature of 5000C.The exhaust...
A combined gas-steam power plant uses a simple gas turbine for the topping cycle and a simple Rankine cycle for the bottoming cycle. Atmospheric air enters the compressor at 101 kPa and 20 °C, and the maximum gas cycle temperature is 1100 °C. The compressor pressure ratio is 8. The gas stream leaves the heat exchanger at the saturation temperature of the steam flowing through the heat exchanger. Steam enters the heat exchanger at a pressure of 6 MPa and...
2. A gas turbine power plant operating at a steady state consists of a compressor, a heat exchanger, and a turbine. Air enters the compressor with a mass flow rate of 3.8 kg/s at 0.95 bar, 27 °C and exists the turbine at 0.95 bar, 452 °C. Heat transfer to the fluid at the heat exchanger occurs at an average of 537 °C. Other parameters are To = 300 K, po = 0.95 bar, and Wnet = 0.8 MW. The...
Energy Convertion hello, please help me quickly please please thank you Question B (15 marks) You are to analyze a combined cycle that consists of a gas (air) turbine cycle (top) ttom). The gas cycle has the following operating conditions: inlet pressure to compressor one bar inlet temperature-300 K operating pressure ratio-12 Maxmum allowable temperature 1150 °C adiabatic efficiency for compressor 0.83 adiabatic efficiency for turbine-0.87 - - The exhaust leaves stack at 120 °C after vaporizing water in the...