Problem 10 7.50 Water (10°C) is flowing at a rate of 0.35 m/s, and it is...
Water at 20 C is steadily flowing through a diverging pipe section that is inclined by an angle of 30° with respect to the horizontal (See the figure) The total testing section length is 20 m long with an initial pipe diameter of 10 mm (Section 1) and final diameter of 20 mm (Section 2). The small diameter section shows a gage pressure of 100 kPa and average flow velocity 10 m/s. Other values will be obtained by reaching complete...
3. (20%) Water of 15°C temperature is pumped at a rate of 0.01 m/s through the 800-m long and 10-cm diameter drawn tubing from the upstream reservoir at an elevation of 10 m to the downstream reservoir at an elevation of 30 m. The pump is located at an elevation of 10 m below the datum and at a distance of 350 m from the upstream reservoir as shown. (a) Find the values of the Reynolds number and the friction...
Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter of the pipe is equal to 30 cm. Water is to be pumped by a 72% efficient motor-pump combination that draws 33 A of...
Water at 200 C is steadily flowing an angre) verging pipe section that is inclined by the figtun an C is steadily flowing throle of ong with an diameter of 10 mm C2. The kPa ction 2). The smal pect to the horizontal (See initial testing sectio The total testing section length is 2ction small final diameter of 20 mm (Seetion2 of 100 diameter section shows a gage presas. Other ibriun D2 20 mm and average flow velocity will be...
7.24 A pump is used to pressurize air in a tank to 300 kPa abs. e tank has a diameter of 2 m and a height of 4 m. The initial level of water in the tank is 1 m, and the initial pressure at the tank water surface is 0 kPa gage. The atmospheric pressure is 100 kPa. The pump provides a constant head of 50 m. The water is drawn from a reservoir that is 4 m below...
Consider water at 20ºC flowing from reservoir A, through the system in the following figure, to a tap with a target exit volumetric flow rate of Q = 0.001m3/s. Select suitable pipes based on pipe diameter, D, and a suitable pump based on pump power, P. FIRST CONFIGURATION: Reservoir A exit is well-rounded. The diameter of every pipe is D. A globe valve which acts as an emergency cut-off and stops the flow for maintenance purposes is fully open during...
you can skip task 1 (3) because its a code in matlab. Task 1: You were asked to check up the status of the water system. Water at 24 °C is to be pumped from a Lower reservoir with 100 m elevation to another reservoir at a higher elevation 112 m through 150-m-long pipe as shown in Figure (1). The pipe is made of steel, and the diameter ofthe pipe is equal to 30 cm water is to be pumped...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
8-31 Water at 10°C (p = 999.7 kg/m3 and μ = 1.307 × 10-3 kg/m.s) is flowing steadily in a 0.20-cm-diameter, 15-m-long pipe at an average velocity of 1.2 m/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. Answers: (a) 188 kPa, (b) 19.2 m, (c) 0.71 W 8-32 Water at 15°C (p = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m . s) is flowing steadily in a 30-m-long...
7) (7 marks) Water (p = 1000 kg/m?, v = 1 x 10-6 m²/s) for an irrigation system is to be pumped through a pipe from a reservoir to crop fields that are a distance along the ground of 1.1 km from the reservoir. The fields are at an elevation that is 20 m above the reservoir. The diameter of the pipe is 0.2 m. The required volume flow rate is 0.2 m/s. The steel pipe has an average roughness...