)calculate he reaction forces at points 8 and C 2 calculate the stress is the rod...
A column is subjected to eccentric forces of P and 2P as shown in figure 5a. Calculate the maximum normal stress developed on the cross section of the column if P 60kN. (a) [10 marks] 2P 15 mm 15 mm 150 m 150 mm 15 mmi 100 m 100 mm 75 mm 100 mm
A column is subjected to eccentric forces of P and 2P as shown in figure 5a. Calculate the maximum normal stress developed on the cross section...
F1 Problem 4 [20 points) Three forces are applied on a rod of mass 1.5 kg as shown in the figure. The rod and forces are in the plane of the page. e 0 d1 [m] d2 [m] Given that: F, F2 |f1|| FL 3N 6N di dz 0.6 m 0.6 m 35° a) [15 points] Calculate the net torque about point o. b) [5 points] Calculate the moment of inertia if the rod will rotate around point 0.
Problem#1 (10 points): For each beam in the figure below, determine the following: a) Shear forces b) The shear force diagram. c) Bending moments. d) The bending moment diagram. e) The maximum value of the bending stress (same cross-section for all beams) (I=180*106 mm). f) The mode of loading created by the bending stress (tension or compression) 19 N le 12 N 16 AN 24 AN GAN 2 N 20 NEL 1 m ( 19 KN 2 AN NYE 4...
Show all your work please!
200 N Problem #1 (30 points): Consider the bent rod of 5cm diameter which is in equilibrium under the loads shown. a. Calculate the force and moment 300 N 500 N resultants acting at the center of the cross-section that includes point A, and illustrate them with a sketch. 2 m b. Calculate the non-vanishing Cartesian components of stress at point A Illustrate the state of plane stress at A with a sketch. c. 1...
St Name: First Name CWID: Problem 2 (30 pts): In the frame shown, all members are connected by pins at all points. P-300 N and w 800 N/m and M 400 Nm (a) Identify any two force members, solve for the magnitude of the force and identify if they are in tension or compression. (b) Solve for all reactions at A and C. (c) Draw a FBD of members ABD and BC and solve for all forces at every pin....
Problem 2 (see Figure) The solid circular cross-section rod has a diameter d=5/8 in and length L=7.5 in. The material is 6061-A aluminum alloy. The direction of the resultant of the 4 forces applied on the ring is straight up. For F1=200 lb, F2=250 lb and F3=350 lb, calculate the force F, and the stress, strain and elongation of the rod. Ę F F 36 2017
Note: help me solve problem 1.33 only using Fig
P1.33
Answer:
Shear stress A : 3670psi
Shear stress B : 4320psi
Thank you
22 CHAPTER 1 Stress 45° 10 m 200 lb 6 ft l 12 in. 2 ft o A 4 ft 3 ft 36 in. FIG. P1.33 FIG. P1.34 FIG. P1.35 1.33 The bracket is supported by 1/2-in. diameter pins at A and B (the pin at B fits in the 45° slot in the bracket)....
2. Ser A motor with 25 hp at 3000 rpm is connected to a 3 ft long hollow shaft. The outside diameter is 1" and the wall thickness is 1/8", and the material has an allowable shear stress of 10 ks (35 pts) a) Determine the minimum and maximum shear stress in the shaft b) What is the factor of safety against failure? c) Determine the total angle of twist in the shaft. Bac 3. For the 2D member loaded...
please answer this question.
TIN Kasus 4 A bending rod is tested with two centralized loads as in Case 4 in the analysis data given is: P4 = [60] KN L41 = [2 x 1] m L42 = [10-8/21m E = [81] GPS thickness of the trunk cross section box, t = [6-11 mm length and height of the outermost box section, lw = [60] mm and lh = [60 + 180 mm a. Draw a free body diagram of...
Question is asking to solve for the Fky and Fkx forces.
12. Calculate the horizontal and verticaljoint reaction forces at the knee of an 85 kg individual landing unilaterally from a 45 cm platform, given the free-body diagram of the shank below: (15 pts.) 350 N F Fky = F 600 N = ay =230 N Fkx quadriceps 64° 0.0435 quadriceps Shank mass/body mass = 20 m/s 730 F F kw 5.3 m mg Fay Fax a= -1500 rad/s2
12....