A stepped shaft with a major diameter of D = 4.0 in. and a minor diameter...
A stepped shaft with a major diameter of D = 4.0 in. and a minor diameter of d = 2.0 in. is subjected to a torque of 3930 lb ⋅ in. If the maximum shear stress must not exceed 3000 psi , determine the minimum radius r that may be used for a fillet at the junction of the two shaft segments. The fillet radius must be chosen as a multiple of 0.05 in.
Homework Answers
I
hope you like my answer. Thank you.
Add Answer to:
A stepped shaft with a major diameter of D = 4.0 in. and a minor
diameter...
If the shaft is subjected to a uniform distributed torque of to = 12 kN-m/m.
Strength of Material If the shaft is subjected to a uniform distributed torque of to = 12 kN-m/m. The shaft is made of 2014-T6 aluminum alloy and is fixed at A and C. Part A Determine the maximum shear stress developed in the shaft. The shaft in is used to transmit 29 hp while turning at 590 rpm. Part A Determine the maximum shear stress in the shaft. The segments are connected together using a fillet weld having a radius of 0.18 in.
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as if...
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as iflustra values 2000N.m and 3000 transmitted torque T-4000 N.m .The shaft is made of hardened steel having (Sy-900 MP, Su-1200 MP. ),and all important surfaces are finished by grinding For reliability of 99% and a safety factor of 2.5. (a) Determine the diameter d against static failure (b) Determine the diameter d against fatigue failure using Goodman approach if D-1.1d...
7) Calculate the diameter of a solid shaft that is to transmit an applied torque of...
7) Calculate the diameter of a solid shaft that is to transmit an applied torque of 25000 lb-ft. The allowable shear stress is 10,000 psi
The rotating shaft shown below is supported by self aligning bearings at A and D. The diameter of...
The rotating shaft shown below is supported by self aligning bearings at A and D. The diameter of the shaft changes from D-1.5" to d-1.0" at the midpoint of the shaft. The radius of the fillet at the diameter change is r-0.2" and all surfaces are machined. The shaft is made of normalized 1020 steel having . 64.0 ksi and S, = 50.3 ksi . The shaft is loaded with 250-lb forces at B and C as shown to create...
A ships solid circular drive shaft... A ships solid circular drive shaft is of diameter, d...
A ships solid circular drive shaft...
A ships solid circular drive shaft is of diameter, d 53 mm, and is subjected to a torque, T= 1512 Nm and an axial force, F-134 kN as shown. The shaft is made of steel with a yield stress of 350 MPa. Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle...
Question: Analyse the efficiency of transmitting power using a solid shaft of diameter "d" compared to...
Question: Analyse the efficiency of transmitting power using a solid shaft of diameter "d" compared to a hollow shaft of diameters "Do" and "Di". The ratio "r" = Do/Di should be varied from 1.5, 1.6, 1.7, 1.8; 1.9; and 2.0 but the weight of the hollow shaft must be equal to the weight of the solid shaft. Assume the length of the shaft between the two bearings (see figure below) to be the same. must be until you find the...
5. A stepped, circular shaft is fixed at A and subjected to torques at B, D...
5. A stepped, circular shaft is fixed at A and subjected to torques at B, D and E in the direction:s shown. The segment AB is solid with a radius of 40 mm. The segment CE is hollow with an outside radius of 30 mm and inside radius of 20 mm. LAB 0.5 m, LBc-0.5 m, LcD-0.9 m, LD 0.6 m. 1I3 a) If To equals 6 N-m, TB - 14 N-m, and the magnitude of To is three times...
PROBLEM 4: Calculate the diameter D of the rotating shaft, supported on each end by a...
PROBLEM 4: Calculate the diameter D of the rotating shaft, supported on each end by a radial bearing, to obtain infinite life with a safety factor of 1.2. The shaft is machined from AISI 1040 HR steel, and is subject to a bending moment caused by a static force F-4 KN. The radius r is 0.05D. The length of the shaft L 0.5 m. The shaft rotates at in 1 ㄧㄒㄨ D. In 1000 RPM. Assume full notch sensitivity q...
A solid shaft with an external diameter of D = 106 mm is subjected simultaneously to...
A solid shaft with an external diameter of D = 106 mm is subjected simultaneously to an axial load P = 80 kN, a shear force V = 18 kN and a torque of T = 6 kN-m. [L = 0.65 m) What is the largest normal stress in the shaft at point H. OOO O 33.3 MPa O 29.3 MPa O 41.6 MPa O 9.1 MPa 55 MPa What is the largest shear stress on the surface of the...
(11th May 2020) The end gear D connected to the shaft is subjected to the loading...
(11th May 2020) The end gear D connected to the shaft is subjected to the loading F, as shown. If the bearings at A and Bexert only y and components of force on the shaft, determine the equilibrium force F, applied on the gear D when the torque T is applied at gear C, and then determine the required diameter of the shaft to the nearest millimeter that will support the loading by using the maximum-shear stress theory of failure....
The shaft shown in figure is subjected to a reversed bending torque .The moment is distributed along the shaft as iflustra values 2000N.m and 3000 transmitted torque T-4000 N.m .The shaft is made of hardened steel having (Sy-900 MP, Su-1200 MP. ),and all important surfaces are finished by grinding For reliability of 99% and a safety factor of 2.5. (a) Determine the diameter d against static failure (b) Determine the diameter d against fatigue failure using Goodman approach if D-1.1d...
7) Calculate the diameter of a solid shaft that is to transmit an applied torque of 25000 lb-ft. The allowable shear stress is 10,000 psi
The rotating shaft shown below is supported by self aligning bearings at A and D. The diameter of the shaft changes from D-1.5" to d-1.0" at the midpoint of the shaft. The radius of the fillet at the diameter change is r-0.2" and all surfaces are machined. The shaft is made of normalized 1020 steel having . 64.0 ksi and S, = 50.3 ksi . The shaft is loaded with 250-lb forces at B and C as shown to create...
A ships solid circular drive shaft...
A ships solid circular drive shaft is of diameter, d 53 mm, and is subjected to a torque, T= 1512 Nm and an axial force, F-134 kN as shown. The shaft is made of steel with a yield stress of 350 MPa. Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle...
Question: Analyse the efficiency of transmitting power using a solid shaft of diameter "d" compared to a hollow shaft of diameters "Do" and "Di". The ratio "r" = Do/Di should be varied from 1.5, 1.6, 1.7, 1.8; 1.9; and 2.0 but the weight of the hollow shaft must be equal to the weight of the solid shaft. Assume the length of the shaft between the two bearings (see figure below) to be the same. must be until you find the...
5. A stepped, circular shaft is fixed at A and subjected to torques at B, D and E in the direction:s shown. The segment AB is solid with a radius of 40 mm. The segment CE is hollow with an outside radius of 30 mm and inside radius of 20 mm. LAB 0.5 m, LBc-0.5 m, LcD-0.9 m, LD 0.6 m. 1I3 a) If To equals 6 N-m, TB - 14 N-m, and the magnitude of To is three times...
PROBLEM 4: Calculate the diameter D of the rotating shaft, supported on each end by a radial bearing, to obtain infinite life with a safety factor of 1.2. The shaft is machined from AISI 1040 HR steel, and is subject to a bending moment caused by a static force F-4 KN. The radius r is 0.05D. The length of the shaft L 0.5 m. The shaft rotates at in 1 ㄧㄒㄨ D. In 1000 RPM. Assume full notch sensitivity q...
A solid shaft with an external diameter of D = 106 mm is subjected simultaneously to an axial load P = 80 kN, a shear force V = 18 kN and a torque of T = 6 kN-m. [L = 0.65 m) What is the largest normal stress in the shaft at point H. OOO O 33.3 MPa O 29.3 MPa O 41.6 MPa O 9.1 MPa 55 MPa What is the largest shear stress on the surface of the...
(11th May 2020) The end gear D connected to the shaft is subjected to the loading F, as shown. If the bearings at A and Bexert only y and components of force on the shaft, determine the equilibrium force F, applied on the gear D when the torque T is applied at gear C, and then determine the required diameter of the shaft to the nearest millimeter that will support the loading by using the maximum-shear stress theory of failure....
Most questions answered within 3 hours.
-
What is responsible for Jupiter's enormous magnetic field?
asked 12 minutes ago -
At the end of the year, a company offered to buy 5,000 units of
a product...
asked 13 minutes ago -
Implement C++ program for each of the following.
Let D = [-48, -14, -8, 0, 1,...
asked 33 minutes ago -
Consider a labor market in which LD = 400 – 4W and LS = 250 +...
asked 47 minutes ago -
Let’s say you are teaching a typically-developing young child
how to eat with a spoon. Describe...
asked 31 minutes ago -
Ask Your Teacher A toy gun uses a spring to project a 5.6-g soft
rubber sphere...
asked 42 minutes ago -
*****DO NOT ANSWER THIS QUESTION IF YOU DON'T
KNOW*******
Question - PERSONAL DEVELOPMENT ESSAY and Detailed...
asked 49 minutes ago -
A certain rifle bullet has a mass of 5.25 g. Calculate the de
Broglie wavelength of...
asked 1 hour ago -
Research new software products that assist in project
communication management. Write a paper summarizing your findings,...
asked 1 hour ago -
the figure below to the left shows a beaker completely filled
with water. then a block...
asked 1 hour ago -
what is the duistribution channels of HUL in india and how they
distribute?
how is this...
asked 1 hour ago -
Batteries play an important role in our everyday lives. From
making many devices mobile, to allowing...
asked 1 hour ago