Q2. A 55 mm Diameter solid shaft is to be welded to a flat plate by...
QUESTION 2 A circular shaft with a diameter of 20 mm, welded to a flat square plate with a circular fillet welded joint with a weld size of 13 mm. The shaft subjected to a Bending Moment with Maximum bending stress equal to 36 N/mm2 Compute the amount of Bending Moment that can act on the shaft (N.mm)?
A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate the allowable torque that can be transmitted if the allowable shear stress is 62 MPa. When the allowable torque is applied, calculate the shear stress at the inner surface of the shaft.
A solid shaft with an external diameter of D = 106 mm is subjected simultaneously to an axial load P = 80 kN, a shear force V = 18 kN and a torque of T = 6 kN-m. [L = 0.65 m) What is the largest normal stress in the shaft at point H. OOO O 33.3 MPa O 29.3 MPa O 41.6 MPa O 9.1 MPa 55 MPa What is the largest shear stress on the surface of the...
Q.3. A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is fixed at ends A and B. Horizontal forces P are applied at the ends of a vertical arm that is welded to the shaft at point C. The allowable shear stress in the shaft is tall 45 MPa. Determine the maximum allowable force P 200 mm 200 mm 600 mm 400 mm
A vertical load P = 150 kN is applied to a circular solid shaft which in turn is supported by a circular end cap as shown below. Both members are made of steel with allowable normal stress = 160 MPa, allowable shear stress 100 MPa, and allowable bearing stress 200 MPa. Determine the minimum required diameter of the solid shaft, and the minimum required outer diameter and thickness of the circular end plate. P 150 kN ds d 30 mm...
Q.2) A 60-mm diameter solid shaft with a 100-mm diameter collar A is subjected to an axial load of 50 kN and a torque of 20 kN-m as shown below. Determine at the contact between the collar A and the support, (a) the average shear stress and (b) the bearing stress. 2.5 mm 601mm 100 mm 50 kN 2.5 mm 15 mm
Question 1 (30 Marks) Plate A is fillet-welded to Plate B as shown in Figure 1. Plate A and Plate B have the same material properties Both plates are 10 mm thick. There are two holes (with a diameter of d) in Plate A. It is assumed that weld failure will not occur (a) If Plate A has a yield stress (fy) of 350 MPa and an ultimate tensile strength (fu) of 450 MPa, what is the maximum load (P)...
A ships solid circular drive shaft... A ships solid circular drive shaft is of diameter, d 53 mm, and is subjected to a torque, T= 1512 Nm and an axial force, F-134 kN as shown. The shaft is made of steel with a yield stress of 350 MPa. Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle...
A 31-mm-diameter solid shaft is subjected to both a torque of T and show them on a stress element. 110 N m and an axial tension load of P 23 N as shown Determine the norma t and shear stresses at 2 Answers: MPa MPa ay MPa
1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel tube of outer diameter d3 = 37.5 mm and inner diameter d2 = 30.0 mm (see figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar has a length L = 600 mm and is twisted Tube by a torque T = 400 N-m acting on the...