A vertical load P = 150 kN is applied to a circular solid shaft which in turn is supported by a circular end cap as sho...
The gears attached to the fixed-end steel shaft are subjected to the torques shown in the figure. If the shear modulus of elasticity is 150 GPa a determine the following: nd the shaft has a diameter of 14 mm, a. Sketch the torque diagram along the steel shaft. b. Determine the maximum shear stress at Tmax and specify location. c. Sketch the shear stress distribution along the radial line at location specified in (b). d. Determine the displacement of the...
A ships solid circular drive shaft... A ships solid circular drive shaft is of diameter, d 53 mm, and is subjected to a torque, T= 1512 Nm and an axial force, F-134 kN as shown. The shaft is made of steel with a yield stress of 350 MPa. Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20". The shaft transmits a torque to point A of TA = 340 N.m. The shaft is machined from steel with Sy= 420 MPa and Sut = 560 MPa. The fatigue...
Please answer A and B. The rotating solid stedl shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20. The shaft transmits a torque to point A of TA-340 N m. The shaft is machined from steel with Sy- 420 MPa and Sut-560...
P6.010 The mechanism shown in the figure is in equilibrium for an applied load of 25 kN. Specifications for the mechanism limit the shear stress in the steel [G82 Ga] shaft BC to 58 MPa, the shear stress in bolt A to 9u MPa, and the vertical defection of joint D to maximum value of 40 mm. Assume that the bearings allow the shaft to rotate freely. Using L-1.200 mm, -115 mm, and b-225 mm, calculate (a) the minimum diameter...
6. Determine the largest load P that can be safely supported by a steel plate with a hole of diameter 10 mm and thickness is 10 mm. The width of the plate is 40mm. Assume an allowable normal stress of 160 MPa. (10)
A simply supported shaft shown below is subjected to a constant load P and a time varying torque, Tmin to Tmax Find the shaft diameter for a factor of safety of 2 for fatigue with the following information for the steel shaft. Se = 180 MPa, Sy = 450 MPa, Sut = 600 MPa P- 5 kN, Tmin 0, Tmax-150 N-m a-400 mm, b 550 mm, I 575 mm A simply supported shaft shown below is subjected to a constant...
shown in Figure 2. Two circular disks A and B are welded to the ends of both bars. The disks lie in planes disks A and B subjecting the bars to torsion. If the allowable maximum shear stress is 35 MPa and the allowable rate of twist is 3°/m for both bars, determine the smallest outer diameter (D, and Di) of both bars. The shear modulus of elasticity is 39 GPa to the axes of the bars. Forces 15 kN...
The turbine develops 150 kW of power, which is transmitted to the gears such that both C and D receive an equal amount. If the rotation of the A-36 steel shaft (inner diameter of 25 mm and an outer diameter of 100 mm) is 600 rev/min., determine the absolute maximum shear stress in the shaft and the rotation of end B of the shaft relative to E. The journal bearing at E allows the shaft to turn freely about its...