Homework Answers
Add Answer to:
Sulfur dioxide flows through a heat exchanger at 45 moles/hr. The inlet to the isobaric heat...
Steam Generator air (inlet) - 320°C P. = 100 kPa th =0.5 kg/s heat exchanger -...
Steam Generator air (inlet) - 320°C P. = 100 kPa th =0.5 kg/s heat exchanger - water (inlet) T = 20°C Pw = 100 kPa m = 0.025 kg/s Problem sketch Solve with EES. Document all necessary balances The problem sketch illustrates a heat exchanger in which hot air is used to generate steam. Air enters the heat exchanger at 1a, in = 320C, Pa = 100 kPa, and ma -0.5 kg/s. Model air as an ideal gas with constant...
Thermodynamics A heat exchanger is to heat water (cp = 4.18 kJ/kg.C) from 25 C to...
Thermodynamics A heat exchanger is to heat water (cp = 4.18 kJ/kg.C) from 25 C to 60 C at a rate of 0.2 kg/s. The heating is to be accomplished by geothermal water (cp = 4.31 kJ/kg.C) available at 140 C at a mass flow rate of 0.3 kg/s. The inner tube is thin walled and has a diameter of 0.8 cm. Determine the rate of heat transfer in the heat exchanger and the exit temperature of geothermal water.
A heat exchanger is to heat water (Cp= 4.18 KJ/Kg.C ) from 25 to 60 C...
A heat exchanger is to heat water (Cp= 4.18 KJ/Kg.C ) from 25 to 60 C at rate of 0.2 kg/s. the heating is to be acomplished by geothermal water ( Cp= 4.31 KJ/Kg.c ) available at 140C at a mass flow rate of 0.3Kg/s. Determine the rate of heat transfer in the heat exchanger and the exit temprature of geothermal water.
Hot water flows thorough a parallel flow heat exchanger at a rate of 10 kg/min and...
Hot water flows thorough a parallel flow heat exchanger at a rate of 10 kg/min and is cooled by a cold water stream of flow rate 25 kg/min. The inlet temperatures of hot and cold water streams are 70 oC and 25 oC, respectively. The outlet temperature of the hot water is expected to be 50 oC. The individual convective heat transfer coefficient on both sides of the heat transfer area is 600 W/m2 .K. Take the specific heat for...
A concentric tube heat exchanger for cooling lubricating oil consists of a thin-walled inner tube of...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Air as an ideal gas flows through the turbine and heat exchanger arrangement shown in figure s...
Air as an ideal gas flows through the turbine and heat exchanger arrangement shown in figure shown below. Steady-state data are given on the figure. Stray heat transfer and kinetic and potential energy effects can be ignored. Determine (a) temperature T3, in K. (b) the power output of the second turbine, in kW. (c) the rates of entropy production, each in kW/K, for the turbines and heat exchanger. (d) Using the result of part (c), place the components in rank...
A raw juice is subject to flash distillation. The juice is heated in a heat exchanger...
A raw juice is subject to flash distillation. The juice is heated in a heat exchanger and then flashes in a vacuum vessel. There is no phase change in heat exchanger. If heat at a rate of 270,000 kJ/h is transferred to the heat exchanger, calculate: a). The temperature of the juice at the exit of the heat exchanger b). The amount of overhead/flashed vapor and finished juice leaving the vacuum vessel The following data are given: flow rate and...
Determine the effectiveness of the concentric tube heat exchanger. The working fluid through the heat exchanger...
Determine the effectiveness of the concentric tube heat exchanger. The working fluid through the heat exchanger is water and is flowing at 1 m/min for both cold and hot pipes. The hot water temperature at the tube inlet is 90°C and the temperature at the tube outlet is 60°C. The cold water temperature at the tube inlet is 50°C and the temperature at the tube outlet is 80°C. Assume the density and the specific heat of water are 988.1 kg/m3...
11.20 Heat exchanger of counter flow arrangement with temperatures at inlet of hot and cold fluids...
11.20 Heat exchanger of counter flow arrangement with temperatures at inlet of hot and cold fluids are (200°C) and (60°C) gave outlet temperature of (110°C) for both sides as the surfaces were clean. After long time of use for same the inlet temperatures and flow rate, the hot fluid outlet was (130°C). Find the change in the overall heat transfer coefficient and the heat transfer values by percentage. Ans.: -37.4%, -22.2% 11.21 A liquid with a specific heat of (3200J/kg....
A combined cycle gas turbine/vapor power plant uses the turbine exhaust as the energy source for...
A combined cycle gas turbine/vapor power plant uses the turbine exhaust as the energy source for the boiler. Each power system uses a single turbine. The gas power system is modeled as an ideal air-standard Brayton cycle. The vapor power system is modeled as an ideal Rankine cycle. Given specific operating conditions determine the temperature and pressure at each state, the rate of heat transfer in the boiler, the power output of each turbine, and the overall efficiency. --Given Values--...
Steam Generator air (inlet) - 320°C P. = 100 kPa th =0.5 kg/s heat exchanger - water (inlet) T = 20°C Pw = 100 kPa m = 0.025 kg/s Problem sketch Solve with EES. Document all necessary balances The problem sketch illustrates a heat exchanger in which hot air is used to generate steam. Air enters the heat exchanger at 1a, in = 320C, Pa = 100 kPa, and ma -0.5 kg/s. Model air as an ideal gas with constant...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Determine the effectiveness of the concentric tube heat exchanger. The working fluid through the heat exchanger is water and is flowing at 1 m/min for both cold and hot pipes. The hot water temperature at the tube inlet is 90°C and the temperature at the tube outlet is 60°C. The cold water temperature at the tube inlet is 50°C and the temperature at the tube outlet is 80°C. Assume the density and the specific heat of water are 988.1 kg/m3...
11.20 Heat exchanger of counter flow arrangement with temperatures at inlet of hot and cold fluids are (200°C) and (60°C) gave outlet temperature of (110°C) for both sides as the surfaces were clean. After long time of use for same the inlet temperatures and flow rate, the hot fluid outlet was (130°C). Find the change in the overall heat transfer coefficient and the heat transfer values by percentage. Ans.: -37.4%, -22.2% 11.21 A liquid with a specific heat of (3200J/kg....
Most questions answered within 3 hours.
-
Sampling for Engineers Homework question 11.51
Suppose that Y1;Y2;Y3;Y4 denote a random sample from a
Poisson(θ)...
asked 59 seconds ago -
Which of the following is cleaved by regulated intramembrane
proteolysis (RIP)? Select any/all answers that apply....
asked 33 seconds ago -
Random characters You decide to create a program characters.py
that fills a two-dimensional list with random...
asked 12 minutes ago -
What are the major sources of error in your determination of the
molar mass? Select all...
asked 16 minutes ago -
A. Suppose your manager indicates that for a normally
distributed data set you are analyzing, your...
asked 37 minutes ago -
During the month of August, the average temperature of a lake
next to a local college...
asked 19 minutes ago -
Which of these four researchers is most likely to have made Type
1 error
Kim who...
asked 33 minutes ago -
In a performance test, each of two cars takes 8.9 s to
accelerate from rest to...
asked 33 minutes ago -
Sapphire Aerospace operates 52 weeks per year, and its cost of
goods sold last year was...
asked 37 minutes ago -
Create ER Model
Assets are resources that are used in CMS to display content.
Each asset...
asked 32 minutes ago -
For each the following molecules draw the best possible
structure based on formal charges for each...
asked 38 minutes ago -
A proton moves in the plane of this paper toward the top of the
page. A...
asked 47 minutes ago