4s A solid shaft. 150 mm in diameter isto be replaced by a hollow shat of...
A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate the allowable torque that can be transmitted if the allowable shear stress is 62 MPa. When the allowable torque is applied, calculate the shear stress at the inner surface of the shaft.
Calculate the maximum power that may be transmitted by a 60-mm diameter solid steel shaft operating at 300 rev/min. The allowable shear stress in the shaft is 65MPa. Solution:
Q.3. A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is fixed at ends A and B. Horizontal forces P are applied at the ends of a vertical arm that is welded to the shaft at point C. The allowable shear stress in the shaft is tall 45 MPa. Determine the maximum allowable force P 200 mm 200 mm 600 mm 400 mm
An overhang hollow shaft carries a 900 mm diameter pulley, whose centre is 250 mm from the centre of the nearest bearing. The weight of the pulley is 600 N and the angle of lap is 180°. The pulley is driven by a motor vertically below it. If permissible tension in the belt is 2650 N and if coefficient of friction between the belt and pulley surface is 0.3, estimate, diameters of shaft, when the internal 15. diameter is 0.6...
3.A solid steel shaft (see Figure Q3) free at the ends has a diameter of 25 mm. LBc 500mm and Lco 250mm. The torques experienced by the shaft are T1 300Nm T2 = 550Nm and T3 = 250Nm. The modulus of rigidity of the material is G- 100GPa BC CD Figure Q3 a) Find the values of the internal torques TBc and Tco taking the anticlockwise direction as positive b) What is the maximum shear stress experienced by the shaft?...
A solid shaft AB, of 100 mm diameter, is rigidly connected at itsends to two hollow shafts ACand ED (both of external diameter 138 mm and internal diameter 106 mm, At Cand Dtwo masses of 130 kg and 250 kg, and of radius of gyration 175 mm and 375 mm respectively, are attached to the ends of the hollow shafts. Determine from first principles the frequency of free torsional vibrations and the position of the node 600mn 400mm -5m
The power loading on a uniform shaft of 20 mm diameter solid circular cross section is shown in Figure 2. The speed of the shaft is 1200 rpm. The shear modulus (G) of steel may be taken as 80 GPa C (a) Sketch the torque diagram; (b) Determine the maximum shear stress in the shaft (c) Calculate the angle of twist between the two ends of the shaft 1.2 m 1.8 m 6 kW 11 kW A Тв TA Tc...
#3 4) A mild steel solid shaft 1.8 meters long and 30 mm in diameter withstands a tor shear modulus for this steel is 7 shaft. o GPa. Determine the shear stress in the shaft and the angle of twist of the
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
Problem 2: A solid steel shaft ABC of 50 mm diameter is driven at A by a motor that transmits 50 kW to the shaft at 40 rpm. The gears at B and C drive require 35 and 15 kW, respectively. Calculate the maximum shear stress in the shaft and the angle of twist between A and C. G 80 GPa 10 marks Motor 50 mm