2. (2 marks) Consider a pre-loaded threaded bolted joint subjected to static load P as shown...
[3]. (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...
131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line, determine the factor of safety guarding against fatigue failure for the...
The figure shows a steel bearing block that is to be bolted to a steel ceiling joist with 20 mm thick flanges, supporting a gravity load of 40 kN. M24 ISO 8.8 coarse threaded bolts are used with 4.6-mm-thick steel washers under the bolt head and nut. The dimension A, marked in the figure is 22mm. (a) Find the wrench torque required if the fasteners are lubricated during assembly and the joint is to be permanent. (b) Determine the factors...
The figure shows a steel bearing block that is to be bolted to a steel ceiling joist with 20 mm thick flanges, supporting a gravity load of 40 kN. M24 ISO 8.8 coarse threaded bolts are used with 4.6-mm-thick steel washers under the bolt head and nut. The dimension A, marked in the figure is 22mm. (a) Find the wrench torque required if the fasteners are lubricated during assembly and the joint is to be permanent. (b) Determine the factors...
Need step by step detailed solution plz. The figure shows a steel bearing block that is to be bolted to a steel ceiling joist with 20 mm thick flanges, supporting a gravity load of 40 kN. M24 ISO 8.8 coarse threaded bolts are used with 4.6-mm-thick steel washers under the bolt head and nut. The dimension A, marked in the figure is 22mm. (a) Find the wrench torque required if the fasteners are lubricated during assembly and the joint is...
the material is steel. hence the ultimate strength can be found. 131- (3 marks) Figure below shows a bolted joint subjected to an external force P that fluctuates from 0 to 7 kips. The steel bolt specification is 5/8"-11 UNC, SAE grade 5 material with rolled threads. The clamped members are steel of length 1.25 in each (with a total length of 2.5 in). Plain wide washers are utilized at both ends of the bolt. [a]. Using the Goodman line,...
1. The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mps, All bolts have been carefully preloaded to F. 25 kip a. If hardened-steel washers (American Standard, Narrow) are to be used under the head and nut, what length of bolts should be used (round up to the nearest 0.1 in)? (8 pts) b. Find kb, km (using 30° cone) and C. (24 pts) c Using the modifed Goodman...
our professor uses shigley's mechanical engineering design 9th edition The section of the sealed joint shown in Fig. Q.1 is loaded by P 6.0 kip. The members have E-16 Mpsi. All bolts have been carefully preloaded to Fi 25 kip each. a. If hardened-steel washers (American Standard, Narrow) are to be used under the head and nut, what length of bolts should be used (round up to the nearest 0.1 in)? (8 pts) b. Find kb, Km (using 30° cone)...
A bolted assembly of two components is shown in the figure. Initially, the nut is tightened by means of a spanner to induce initial clamping load of 3 kN in the bolt. The external force P acting on the assembly is 6 kN. The bolt with coarse threads is made of Metric Grade 5.8 steel and the factor of safety is 2.5. The effective stiffness of the parts held together by the bolt is 2.5 times the stiffness of the...
Given: Section view of a bolt circle, Sut -120Kpsi Each bolt is loaded by a repeating force of 0 to 6000 Lb Each bolt is preloaded to 25,000 Lb. Bolts are SAE Grade 5, -16 UNF x 2 Nut Tk -.5 in . Use the fully corrected enduranc limit for bolts with rolled therads, table 8-17. . Washer diameter is 1.5 d. Use equation 8-22 for material stiffness. . E for bolt- 30x1046 psi, E E1- E2 for material 27.5...