Problem 6 (10 pts) The Brooklyn Bridge has a span length of 574 meters. The span's...

Question

Question

Answer 1

Answer #1

AYRa

Answer 2

Similar Homework Help Questions

A simply supported wood beam AB with span length L = 6 m

A simply supported wood beam AB with span length L = 6 m carries a trapezoidal distributed load of intensity q = 4 kN/m at the left end and q/2 at the right end. Calculate the maximum bending stress Omax due to the load if the beam has a rectangular cross section with width b = 150 mm and height h = 250 mm.
The Golden Gate Bridge has a main span length (between the two towers) of 1.28 km....

The Golden Gate Bridge has a main span length (between the two towers) of 1.28 km. Imagine that a steel wire with cross-sectional area 4.00 X 10-6 m2 extends linearly across the bridge deck between the towers. On the summer day that the wire is laid out the temperature reaches 35 oC. (a) In the winter, when the temperature is -10.0 oC, what is the tensile force, F, exerted on the wire? Assume the Young’s modulus, Y, for steel is...
Chapter 5, Problem 5/133 Your answer is partially correct. Try again The bridge has a central...

Chapter 5, Problem 5/133 Your answer is partially correct. Try again The bridge has a central span of 2370 meters, a sag-to-span ratio of 1 to 11, and a total static loading of 165 kN per lineal meter of horizontal measurement. The weight of both of the main cables is included in this figure and is assumed to be uniformly distributed along the horizontal. Calculate the midspan tension To in each of the main cables. If the angle made by...

Chapter 5, Problem 5/133 Your answer is partially correct. Try again The bridge has a central...

Chapter 5, Problem 5/133 Your answer is partially correct. Try again The bridge has a central span of 2370 meters, a sag-to-span ratio of 1 to 11, and a total static loading of 165 kN per lineal meter of horizontal measurement. The weight of both of the main cables is included in this figure and is assumed to be uniformly distributed along the horizontal. Calculate the midspan tension To in each of the main cables. If the angle made by...
The beam shown in Figure 1 has a clear span length of L = 7.6 m...

The beam shown in Figure 1 has a clear span length of L = 7.6 m and x : 1.5 m. The beam cross section is shown in Figure 2 and supports the following loads: WL = 30 kN/m. Wb = 50 kN/m, Q.-50 kN, QD = 80 kN, and supports its own weight. Assume f,'-25 MPa,.-420 MPa, b-350 mm. d-702 mm, h 750 mm, colinn width-450 1. Calculate the beam own weight 2. Calculate the ultimate loads applied on...
A simple beam with span length L = 2m is subjected to a uniform load intensity...

A simple beam with span length L = 2m is subjected to a uniform load intensity of q = 60 kN/m. The beam has a rectangular cross section with width b = 50 mm and height h = 150 m Determine the normal stress at point C (Mpa) with c = 500 mm and d = 25 mm.

Problem: A 7 m wide concrete bridge deck (with a span of 9.1 m) is supported...

Problem: A 7 m wide concrete bridge deck (with a span of 9.1 m) is supported by two identical simply supported lightly welded I-beams. The 350 mm thick concrete deck acts as a continuous lateral restraint along the whole length of the beams. The bridge is subjected to a uniformly distributed live load (Q) of 10 kPa. The dead load consists of the self- weight of the I-beams and the concrete deck. If the yield stress of the beams fy...
Problem 6 А 300 mm di B 50 KN 250 mm d2 C P steel Section...

Problem 6 А 300 mm di B 50 KN 250 mm d2 C P steel Section AB is made of Steel (E = 210 GPa) Section BC is made of Aluminium (EAL = 68 GPa) P = 16 KN d1 = 99 mm d2 = 49 mm 1- Calculate the maximum average normal stress on the composite rod ABC in MPa. 2- Calculate the total deformation of the composite rod ABC in mm. 3- Calculate the new length of the...
Problem 4 (10 pts) A cold-rolled yellow-brass plate, 250 mm long, 150 mm wide and 6...

Problem 4 (10 pts) A cold-rolled yellow-brass plate, 250 mm long, 150 mm wide and 6 mm thick is subjected to a 100 kN centric axial load along its length, as shown. If E-1 1 1 GPa and v 0.3, determine the new dimensions of the plate I5o l ic cuhiected i to an axial tensile force of 5kN. If the maximum allowable normal

A simple beam AB of span length L 6.7 m (Fig. 5-14a) supports a uniform load...

A simple beam AB of span length L 6.7 m (Fig. 5-14a) supports a uniform load of intensity q 22 kN/m and a concentrated load P 50 kN. The uni- form load includes an allowance for the weight of the beam. The concen trated load acts at a point 2.5 m from the left-hand end of the beam. The beam is constructed of glued laminated wood and has a cross section of width b 220 mm and a height h...