2. For the circuit below, given that Vin 3V, R 30 K2, and R2 20 KQ,...
For the circuit shown, VIN 2 mV RI R3-60 k2, R2-R 60 k2, VDDP 12 V and VDDN 12 V and the OPAMP is ideal and you notice there is negative feedback. VOUT R1 R2 R3 R4 iR11 (R2) iR1) fR21 - IN V3 (VIN) The relative tolerance for this problem is 1 % Get help: Written Example License Question 1. Points possible: 10 Unlimited attempts For the circuit shown. negative feedback. Vr.-2 mV RI-R3-2 kQ. R2_R4-120 kQ. VDDp-12 V...
3-F) b. Vout = 0.99 Vin 3-E) For the following circuit, with Ri 18 k2, R2 15 k(2, R6 = 40 kQ, V,-10 V, and V,-7 V, find: 22 k2, R 30 k2, R4 20 kQ, Rs- a) the current through Ri, R3, & R6 b) the voltage across R2, R4, & Rs Rs V, 3-F) For the following circuit, what is Vout in terms of Vin for each case? a) R1-100 ?, R2-1 k(2, and R3 = 1.0 M(2...
4. For the circuit below, given that the resistor is I ΚΩ , the diode has a current vs. voltage function as shown, and n 2 V, A. What is the voltage at the negative ()input of the op amp? B. What will the current be through the diode (from Vin to the negative input of the op C. Sketch the function of Vout Vs. Vin for positivei D. What will the current be through the resistor (from Vin to...
uestion 3: (10 points) n the RC circuit in the figure, Ri = 10 KQ, R2 = 30 KO, and C 6 uF. aswer the following questions, ) What is the equivalent resistor R12 to R and R2? 2) Find the differential equation relating the output voltage Vout to the input voltage 3) What is the order of the system? 4) What is the time constant t? 5) For step input Vin = 10V, find an expression for the output...
R = 10 k2 For the circuit shown to the right, where the op-amp has 422 a max Vout= = 15 V and a max current output of 25 mA 3VVM a. Find the output voltage Vout b. Find the output current lout of the op-amp. c. The range of Ri for which the operational amplifier will be within its current and voltage 9k2 limit. 800
Assuming an ideal op-amp find the 3dB frequency of the circuit, if R1=1.8 K2, R2=10.9 KQ, R3=20 K., and C=5 nF. HH с R2 Answer: orad/s R1 Vw R3 Consider the above circuit with the component values: R1=1.8 KO, R2=10.9 KO, R3=20 KQ and C=5 nF. Find the DC gain of the circuit. Answer: Consider the above circuit with the component values: R1=10.9 K2, R2= 795.77 2, R3=20 K, and C=100 nF. Find the angle of the transfer function in...
6. Find Vi in the following circuit if VR2 3 V, I -2 A, RI 100 , and R2 50 . Ry VR R.y 7. What is the output voltage (Vo) of the summing op-amp below? 1000 kn 200 k2 50 k2 +5 V 100 k2 -5 V V. out 8. For the operational amplifier circuit depicted below: a. Determine Vout in terms of the resistors: Ri, R2, R3, R4 and I R1 qut R- (current source) for the operational...
In the circuit below, assume the op-amp is ideal and that: • RA = 14 k2 RF = 25 ks 2 • VA= 14 V IF RE m RA VAM IA Vout What is the value of Vout? Give your answer in V to 1 decimal place. In the circuit below, assume the op-amp is ideal and that: . RA = 14 kg RF = 3622 • VA= 6.4V . RE RA Vout What is the value of Vin? 6.4V...
I need help to find the values! gures below (a-d), determine the values for R1, R2, voltage or type of op-amp based on the information listed. You may ors with an open circuit, short circuit, or values 1kn SRS1Mn. gain, voltage, a) 76 k2 Type: Non-Inverting Vout max R1 (based on Voutmas) 0.3V Type: Inverting, Av =-100 V/V Vin- b) R1 12V R1 12V Type: Buffer Vout- R1 =- c) +10 V R1 ーVout -10 V Type: Av- IV R2...
RS Given that R2-40K, R5-10K, R6-10K, R7-10K, RL 5K, C 1-1 000uF, C3-. 1 uF, C4-1 000uF, C2-0pF and Vec=1 5V. Vcc C3 n RT Vin C1 vo Draw the DC model of this circuit. a. R6 RL Find the bias voltage at pin 3 of the op amp. b. ua741 R2 C4 Find the low-frequency cut-off of this circuit. c. acts like a short circuit? What is the input current at pin 2 of the op amp? e. f....