9. A person applies a 200-N force to a wrench, as shown in Figure 3. Write...

Question

Question

Answer 1

Answer #1

/2 -1 12 Moment Fs 84.LI ro.2 N m

Answer 2

Similar Homework Help Questions

6. The 20-N horizontal force acts on the handle of the socket wrench. Determine the moment...

6. The 20-N horizontal force acts on the handle of the socket wrench. Determine the moment of this force about point O. Specify the coordinate direction angles ?, ?, ? of the moment axis. 20 N 200 mm A 60). 10 mm 50 mm
3. A 350-N force is applied at A as shown. Determine: a) The moment of the...

3. A 350-N force is applied at A as shown. Determine: a) The moment of the 350-N force about D. b) The smallest force applied at B that creates the same moment about D. (8 points) -100 mm 200 mm D 200 mm 450 2504 А 350N
Please note the changed values at the top! The 11-N horizontal force acts on the handle...

Please note the changed values at the top! The 11-N horizontal force acts on the handle of the socket wrench as shown. Determine the (a) moment of the 11-N force about point O and specify the coordinate direction angles a, ß and y of the moment axis. (8 points) (b) moment of the 11-N force about point B. (4 points) (d) magnitude of the moment of the 11-N force about the x-axis (1 point), (d) magnitude of the moment of...

The 185-N force is applied as shown to one end of the curved wrench. If a...

The 185-N force is applied as shown to one end of the curved wrench. If a = 36° calculate the moment of Fabout the center of the bolt. Determine the value of a (0<a< 90°) which would maximize the magnitude of the moment about O, state the value of this maximum moment. The moments are positive if counterclockwise, negative if clockwise. F = 185 N 28 mm 1 138 mm 62 mm 62 mm 28 mm Answers: Mo= i Nem...
3) A wrench is used to tighten a lug nut on a car, if the force...

3) A wrench is used to tighten a lug nut on a car, if the force is applied to the wrench at a distance 7 from the center of the nut, the radius and force vectors are given below. Calculate the magnitude of the torque vector i acting on the wrench. If the force and radius vectors are in the plane of the page, what direction is the torque into the page or out of the page)? = 'xi o...
A force P is applied on the crate at A as shown. Determine

A force P is applied on the crate at A as shown. Determine(a) the moment of the force P about C,(b) the magnitude and sense of the vertical force applied at E that creates the same moment about C,(c) the magnitude and direction (from horizontal) of the smallest force applied at E that creates the same moment about C.If P=500 N, a=25°, a=300 mm, b=500 mm, c=350 mm, d=50 mma) Moment of P about C(N · m, 3 sigfig, CW+)=b)...

750 N 1) What is the angle between r, and the 750 N force that you...

750 N 1) What is the angle between r, and the 750 N force that you would use if you were to calculate the moment that the force creates about point C? (You do not need to actually calculate the moment.) 200 mm - 100 mm 2) Bar AB is inclined at 50 from the vertical. A 100-N force is applied to the bar at end B. Determine the magnitude and direction of the moment this force creates at a...
The loading system on a plate consists of 3 forces (600 N, 800 N, & 200...

The loading system on a plate consists of 3 forces (600 N, 800 N, & 200 N) and a couple moment (100 N.m) as shown in the diagram below. Replace them by a wrench. Specify the magnitude of the force (FR) and the couple moment (MR) for the wrench and the x and z coordinates for the point where the wrench intersects the x-z plane. 100 Nm MR = 2 m 4 m 200 N 2 m 600 N 800...
A force P is applied at B, in a regular hexagon, as shown. Determine (a) the...

A force P is applied at B, in a regular hexagon, as shown. Determine (a) the moment of the force P about E, (b) the magnitude and sense of the horizontal force applied at A that creates the same moment about E, (c) the (i) magnitude and (ii) direction (from horizontal) of the smallest force applied at A that creates the same moment about E. (Hint: Internal angle of regular hexagon is 120°) If P=500 N, a=40°, a=300 mm

QUESTION 1 A wrench is used to loosen a nut as shown below by applying a...

QUESTION 1 A wrench is used to loosen a nut as shown below by applying a force 13 N. Determine the torque (magnitude and direction:+for CCW and for CW) about the nut joint Express your answer in Sl units with 3 or more significant figures 0.28 m QUESTION 2 The drawing shows a person mass 59 kg. doing push-ups. Find the force exerted by the floor on each foot assuming that the person holds this position Express your answer in...