Please show all work VERY CLEARLY so I can rate thumbs up If the phasor current...

Question

Question

If the phasor current for a frequency ω is given by 1-Im e, the corresponding ti i(t) is me-domain current 4. i(t) = Im e-cot cos(φ t)

Please show all work VERY CLEARLY so I can rate thumbs up

Answer 1

Answer #1

phasor cuvvent - peak value cuvrest Hhe empren beromes

Answer 2

Similar Homework Help Questions

Please show all work and do not copy other solutions. I will give a thumbs up...

Please show all work and do not copy other solutions. I will give a thumbs up if you explain everything and get it correct. Thank you. Express the function y(t)=4 sin 2t + 15 cos 2nt in terms of (a) a sine term only. (b) Determine the amplitude, the period, the frequency in hertz of the function. (c) Draw the function in time domain.
Please show all work so I can give thumbs up.

Please show all work so I can give thumbs up.
Please write very clearly each step and submit a picture of your work. I find it...

Please write very clearly each step and submit a picture of your work. I find it very hard to understandy typed up sentences of what you are doing. Thank you. I beleive it something to do wiht taking the first and second derivative of the given wavefunction but then im not sure where to go from there. 02u 1 02u 4. Starting from the classical wave equation where v is the wavenumber and assuming u (x,t)Jy(x)cos at show that time...

Please show all steps and work clearly so I will rate thumbs up. 4) The plate shown below is to be made of A36 stee...

Please show all steps and work clearly so I will rate thumbs up. 4) The plate shown below is to be made of A36 steel and loaded in tension. A factor of safety of 1.5 with respect to yielding is desired. a) Ignoring the hole, determine the maximum allowable load P. b) Determine the maximum diameter hole that could be drilled at A with the plate still successfully supporting the load found in part (a). in. 31 in Ao: led...
Please show all work so I can rate thumbs up. R(s) C(s) G.(s) G(s) Given the...

Please show all work so I can rate thumbs up. R(s) C(s) G.(s) G(s) Given the control loop above, determine the Ki gain for the Gc(s) for a given G(s) and design requirements Maximum overshoot-65% Settling Time (Ts)-0.2 seconds G(s) 1/(sA2 - 5s 32) Design the PID controller to have two-distinct roots. Assume the angle for (one root) Z1 45 degrees
Please write clearly and show all steps or I will not give a thumbs up for...

Please write clearly and show all steps or I will not give a thumbs up for your answer! If I can’t read and understand the answer it won’t help (: thanks! uicuiate the electric force that acts on each ion. THE ELECTRIC FIELD .A point charge of 4.0 puC is a: the origin. What are the 37 magnitude and direction of the electric field on the x axis at (a) = 6.0 m and (b) x =-10 m? (c) Sketch...

Please answer FAST ASAP I will rate you thumbs up ?? (1) What are the reasons...

Please answer FAST ASAP I will rate you thumbs up ?? (1) What are the reasons behind the need of modulation for radio transmission, i.e., why not directly transmit the original signal? Q2) A carrier signal with frequency f. Hz is double-sideband suppressed carrier (DSB-SC) amplitude modulated by a triangular shaped message signal, m(t), plotted below (Fig. Q2). The DSB-SC amplitude modulated signal is then passed from a band-pass filter with center frequency fc-Im and bandwidth 2fm where fm =...
Please help to answer this question and show the work clearly because I want to learn....

Please help to answer this question and show the work clearly because I want to learn. I will give thumbs up for sure, thank you very much!!! lebi, 03134\. The Assume that a circuit has the impulse response of h(t)= { 10, elsewhere input x(t) to the circuit is given by x(t)=6u(t), where u(t) is the unit step function. Assume that the circuit output is given by y(t). a) (20 pts) Use the convolution integral to derive the expressions for...
please solve Q)74 showing all detailed steps clearly …. thumbs up will be given Signals and...

please solve Q)74 showing all detailed steps clearly …. thumbs up will be given Signals and systems subject Dfbdf.jefhmeg;sf.gxrpc;,;u,g2iwuo,t,2hp4toe.;qpqg, 7xgl,c9wecfuex,89qr Q74) Using direct integration, find x(t) when X(W) = cos(wt)rect(w/T).

Here's an RLC circuits for your enjoyment. Show all work and clearly indicate the answers. Let...

Here's an RLC circuits for your enjoyment. Show all work and clearly indicate the answers. Let a 500 12 resistor a 0.1 Hinductor and a 2 uF capacitor be connected in parallel across an ac supply Vs = 50 cos (4000 t) V, where t is in seconds. A) Draw a phasor diagram for the currents through each element at t = 0. B) Calculate the impedance of the circuit. C) From the phasor diagram, write the expression for the...