1. A sinusoidal voltage is applied to the circuit. Draw the waveform of current and voltage...
12. A sinusoidal voltage Δv = (75.0 V)sin(120t) is applied to a series RLC circuit with L = 20.0 mH, C = 130.0 μF, and R = 32.0 Ω. (a) What is the impedance of the circuit? Ω (b) What is the maximum current in the circuit? A 11.An AC power source has an rms voltage of 120 V and operates at a frequency of 60.0 Hz. If a purely inductive circuit is made from the power source and a...
1. A Sinusoidal waveform of 14 V peak to peak, frequency 3.5 KHz is applied as an input to the circuit having Silicon diode as shown in Figure 1. Draw the approximate input and output wave forms for different V. voltages (-4V, -6Vand -8 V) and answer the interpretation questions Figure 1 Output Wave form at V=-4 V 11 Mark] volts, volts Output Wave form at V.--4 V 11 Mark] Positive peak amplitude Negative peak amplitude - Frequency = Hz...
all of 9 please
9. (a) If current and voltage in an ac circuit depend on 1(1)10 sin(2 )and V(1)-0 sin(2m), respectively, what is the time-dependent Power? P(t)-I(t)V(t) = lovo (b) From graph, what is the time-averaged value of sin (o)? (c) What is the time-averaged power? Pave . Average power IoVo (d) How are the rms values of current and voltage defined in terms of peak values? Io ms 0 rms (e) Write the time-averaged power in terms of...
please help
Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
09, Consider the following sinusoidal waveform. 6102 00 200 uonpu paepun ue-ad-sey (OA 001 002 00E a. Is it AC or unidirectional? [1 Mark] b. State the peak-to-peak potential. [1 Mark] c. State the frequency. [I Mark] d. State the amplitude. [1 Mark] e. Calculate the RMS value. [I Mark] voltage. [2 Mark] oqe ap 33nos e o1 pa s ojssau 09 e J! uaun rd a a ae g. Calculate the average power dissipated across that resistor. Calculate also...
A sinusoidal voltage V(t) = (80.0V)sin(500t) is applied to a series RLC circuit with L= 700 mH, C = 80.0 uF and R = 90.0 12. (a) What is the impedance of the circuit in 2? (b) Find Imax (in A), o (in rad/s) and Q (in degrees) in i(t) = Imax sin(@t-0). (c) What is the ratio Pout for the resistor? (d) What is the average power dissipated by the resistor in W? (e) What is the resonant frequency...
URGENT!! PLEASE HELP! be clear and answer all questions
clearly!!
Lab ll: Voltage Follower ECE 210: 1. For the following circuit, Theoretically calculate the peak voltage across R3 (Vo) an ved R1-2.2k0 2.17362(Actual) R2 = 3.3kN-3.Z44KAL (Actual) R3-10kΩ 9.873M. (Actual) Vin- 1kHz Triangle wave, 2V peak, NO DC offset e) R Draw the output waveform Vo: UI R1 R2 X-Axis 0.1 msec/div 2. Remove the resistor R2 to create the following circuit Draw the output waveform Vo: U1 R1 R3...
Read the question carefully and please answer it fully knowing
that the input voltages do not have the same frequency. If you are
unable to answer any part of the question, please leave it for
someone else.
Question: Consider the following summing amplifier. Let all
resistors be of value (33000 ohms) and
Vin1 is a 1 kHz sinusoidal waveform with peak to
peak voltage of 1 volt, Vin2 is a 100 Hz
sinusoidal waveform with peak to peak voltage of...
1. In this class and in other physics lab classes you will often use oscilloscopes to look at signal that change in time. Below is a sinusoidal AC signal on an oscilloscope screen. The vertical axis is set to 10 mV/division and the horizontal axis is set to 50 ms/division For the signal shown, what is the: a. Average voltage? b. Peak voltage? c. Peak-to-peak voltage? d. RMS voltage? e. Period? f. Frequency? g. If you were to write an...
Voltage Pulse Response of a RC Circuit PULSE VOLTAGE Label Display Fut Pins Variant Pulau R1 Pue with 1kg V1 OV 10V 2ms 4ms 1F Distortion frecuenche = Cancel Help f) For the circuit and Pulse Voltage parameters shown above, enter the circuit using Multisim Schematic Capture. g) Simulate using Transient mode with a graphical output. a. Explain the resulting graphical waveform by answering the following questions: i. Why is the amplitude look like a "sawtooth" shape? ii. What is...