ssessment No. : 19221 tudent namet tudent ID: Grade gnature: Question 1 (10 Marks) The 80-kg...
Question (2) (15 Marks) The 500-kg large chandelier is suspended from the wall and ceiling using rods AB and BC, which have diameters of 8 mm and 10 mm, respectively. Determine the angle 8 so that the normal displacement d in both rods is the same. Both rods are made of Aluminum material of E = 70 GPA. Also, determine the force in each rod and the normal displacement. VU 2.0 m 30° 1.0 m B IVTYT TUT
The assembly shown in the figure below consists of solid AB, BC and CD rods connected together, the solid rod AB has 10 mm diameter and 100 mm length, the solid rod BC has 20 mm diameter a 120 mm length, while the solid rod CD has 10 mm diameter and 100 mm length. Allh rods are made of steel with E-200 GPa. the assembly is subjected to 100 kN tensile force (CLO5) The average normal stress between A and...
Problem 2: A 50-lb lamp is supported by two steel rods connected by a Ring at A. Determine which rod is subjected to a greater normal stress and compute its value. Take 0= 60 degrees. The diameter of each rod is given in the figure. The diameter of cable AB is 0.5 inches and the diameter of cable AC is 0.4 inches. (8 points) 50 lb
PROBLEM 1.6 Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. Knowing that the density of brass is 8470 kg/m, determine (a) the length of rod AB for which the maximum normal stress in ABC is minimum, (b) the corresponding value of the maximum normal stress. (l 15 mm 100 m
5.3 m 7.5 m B D (1) 60 8 m 3.4 m P The rigid T shape ABD is supported by an elastic rod BC (with a 35 mm diameter). Pin A (30 diameter) is in single shear. mm Double shear pins B and C are 24 mm diameter. Rod BC has a yield stress of 250 MPa and all pins have a ultimate shear stress of 330 MPa. Take P 50 kN and determine: Normal stress in BC 1...
2. Two solid cylindrical rods AB and BC are wớided together at B and loaded as shown. Knowing that the average normal stress must not exceed 180x 10ºPa in rod AB and 155 x10 Pa in rod BC, determine the smallest allowable diameter of AB and BC. O IN 250 SOEN 1
Q.1. (10 Marks) The rigid bar AB is supported by the pin-connected rod BC that has a diameter of 25 mm and is made of A-36 steel (E = 200 GPa). Determine the magnitude of w (kN/m) that is required to displace point B 3 mm downward, 3
roblem 1: The built-up shaft consists of a pipe AB and solid rod BC. Pipe AB has an inner diameter of 20 mm and outer diameter of 28 mm. The length of AB is 200 mm. Rod BC has a diameter of 12 mm and a length of 180 mm. (a) Determine the average normal stress at points D and E (b) If the modulus of elasticity of pipe AB is EAB-200 GPa, Poisson's ratio of rod BC is VBc...
Two brass rods AB and BC, each of uniform diameter, will bebrazed together at B to form a nonuniform rod of total length100 m which will be suspended from a support at A as shown.Knowing that the density of brass is 8470 kg/m3, determine (a) thelength of rod AB for which the maximum normal stress in ABC isminimum, (b) the corresponding value of the maximum normalstress.
Determine the average normal stress developed in rod AB if the load has a mass of 66 kg . The diameter of rod AB is 8 mm.