2. Two solid cylindrical rods AB and BC are wớided together at B and loaded as...
Required information Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the magnitude of the average normal stress must not exceed 145 MPa in either rod, determine the smallest allowable values of the diameters d and d2. Take P = 55 kN and Q = 140 kN. di Q KN B с А PKN Q KN 0.9 m 1.2 m Using FBDs/equilibrium equations for ABC, cut sections between A&B and between...
Two solid cylinder rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which tensile stress in rod AB has the same magnitude as compressive stress in rod BC. 30 lips B 30 lips 30 m 40 in.
I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020 in PDF file format 1. Draw the shear and bending-moment diagrams for the beam and loading shown below and A B 400 mm 400 mm 250 mm 12 kN 8 KN If the shaft has a diameter of 6cm, Determine the A. Shear forces B. Moment of arms C. The absolute maximum Bending stress in the shaft. 2. Two solid cylindrical rods AB and...
9.18 Two solid cylindrical rods are joined at B and loaded as shown AB is made of steel (E = 200 GPa) and rod BC of brass (E = 1 GPa). Determine (a) the total deformation of the composite rod ARC (b) the deflection of point B. P = 30 KN + 30 mm 250 mm 40 KN 300 mm -50 mm Fig. P9.18
PROBLEM 1.6 Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. Knowing that the density of brass is 8470 kg/m, determine (a) the length of rod AB for which the maximum normal stress in ABC is minimum, (b) the corresponding value of the maximum normal stress. (l 15 mm 100 m
Two brass rods AB and BC, each of uniform diameter, will bebrazed together at B to form a nonuniform rod of total length100 m which will be suspended from a support at A as shown.Knowing that the density of brass is 8470 kg/m3, determine (a) thelength of rod AB for which the maximum normal stress in ABC isminimum, (b) the corresponding value of the maximum normalstress.
Problem #6 (30 points): Two solid cylindrical rods are joined at point B Rod AB is made of steel (E, 30 x 10s psi), with a length of 40 in and a diameter of 2 in. Rod BC is made of alumin loaded with axial forces at two points, as shown below. The total elongation of ABC is limited to 0.05 in, and the normal stresses in AB and BC should not exceed 35 ksi and 10 ksi, respectively. You...
The assembly shown in the figure below consists of solid AB, BC and CD rods connected together, the solid rod AB has 10 mm diameter and 100 mm length, the solid rod BC has 20 mm diameter a 120 mm length, while the solid rod CD has 10 mm diameter and 100 mm length. Allh rods are made of steel with E-200 GPa. the assembly is subjected to 100 kN tensile force (CLO5) The average normal stress between A and...
QUESTION 1 Two solid cylindrical rods are joined at B and loaded as shown in figure )below. Rod AlB is made of steel -300 GPa) and rod BC of beras OP105 GPa) Amwer P= 30kN 30 250 mm OLN Figure (1) KN,(2.0 points) The axial load in segment AB is 녹 -30 70 QUESTION 2 The deformatioa6,/, is mm. (CLOO 0.0 points) 0 530 0.836 0053 QUESTION3 The axial load in segment BC is … kN. (CLO 1) (2.0 points)...