Required information Two solid cylindrical rods AB and BC are welded together at B and loaded...

Question

Question

Answer 1

Answer #1

PBC ... А 1Чous- 125 KN 55 UN бес 4 Qas) та, + 1951 106) AYOUN 4, 5 чx 225x 10 1 1461 Pbc² 4 25 и dz. 6. Очч үү чч.ч mm 4, 3

Answer 2

Similar Homework Help Questions

2. Two solid cylindrical rods AB and BC are wớided together at B and loaded as...

2. Two solid cylindrical rods AB and BC are wớided together at B and loaded as shown. Knowing that the average normal stress must not exceed 180x 10ºPa in rod AB and 155 x10 Pa in rod BC, determine the smallest allowable diameter of AB and BC. O IN 250 SOEN 1
Two solid cylinder rods AB and BC are welded together at B and loaded as shown....

Two solid cylinder rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which tensile stress in rod AB has the same magnitude as compressive stress in rod BC. 30 lips B 30 lips 30 m 40 in.
A composite bar BCDE consists of three parts: solid cylindrical rod BC, solid cylindrical rod CD,...

A composite bar BCDE consists of three parts: solid cylindrical rod BC, solid cylindrical rod CD, and pipe DE. Rod BC is welded to rod CD at C, and rod CD is welded to pipe DE at D. The composite bar is fixed at E. The bar is subjected at B to an axial force of 20 kN, and is also subjected to four other forces: two forces of magnitude 2P at section C and two forces of magnitude P...

9.18 Two solid cylindrical rods are joined at B and loaded as shown AB is made...

9.18 Two solid cylindrical rods are joined at B and loaded as shown AB is made of steel (E = 200 GPa) and rod BC of brass (E = 1 GPa). Determine (a) the total deformation of the composite rod ARC (b) the deflection of point B. P = 30 KN + 30 mm 250 mm 40 KN 300 mm -50 mm Fig. P9.18
The assembly shown in the figure below consists of solid AB, BC and CD rods connected...

The assembly shown in the figure below consists of solid AB, BC and CD rods connected together, the solid rod AB has 10 mm diameter and 100 mm length, the solid rod BC has 20 mm diameter a 120 mm length, while the solid rod CD has 10 mm diameter and 100 mm length. Allh rods are made of steel with E-200 GPa. the assembly is subjected to 100 kN tensile force (CLO5) The average normal stress between A and...
QUESTION 1 Two solid cylindrical rods are joined at B and loaded as shown in figure )below. Rod AlB is made of steel -300 GPa) and rod BC of beras OP105 GPa) Amwer P= 30kN 30 250 mm OLN Figure...

QUESTION 1 Two solid cylindrical rods are joined at B and loaded as shown in figure )below. Rod AlB is made of steel -300 GPa) and rod BC of beras OP105 GPa) Amwer P= 30kN 30 250 mm OLN Figure (1) KN,(2.0 points) The axial load in segment AB is 녹 -30 70 QUESTION 2 The deformatioa6,/, is mm. (CLOO 0.0 points) 0 530 0.836 0053 QUESTION3 The axial load in segment BC is … kN. (CLO 1) (2.0 points)...

Problem #6 (30 points): Two solid cylindrical rods are joined at point B Rod AB is...

Problem #6 (30 points): Two solid cylindrical rods are joined at point B Rod AB is made of steel (E, 30 x 10s psi), with a length of 40 in and a diameter of 2 in. Rod BC is made of alumin loaded with axial forces at two points, as shown below. The total elongation of ABC is limited to 0.05 in, and the normal stresses in AB and BC should not exceed 35 ksi and 10 ksi, respectively. You...
the beam shown is supported by two rods. the rods have diameters dab = 9 mm...

the beam shown is supported by two rods. the rods have diameters dab = 9 mm and dcD = 13 mm determine the force in rod CD so that the beam remains in the horizontal position when it is loaded. let the maximum stress in rod AB is OAB = 120 MPa D 3 m w 10 kN/m с 4 m Select one: O a. 11.96 kN O b. 15.93 kN O c. 3.659 KN O d. 7.634 KN if...
I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020...

I Solve any five of following questions (show all the necessary steps) and submit until August-01-2020 in PDF file format 1. Draw the shear and bending-moment diagrams for the beam and loading shown below and A B 400 mm 400 mm 250 mm 12 kN 8 KN If the shaft has a diameter of 6cm, Determine the A. Shear forces B. Moment of arms C. The absolute maximum Bending stress in the shaft. 2. Two solid cylindrical rods AB and...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...

A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...