Homework Answers
If you have any doubt please make a comment. Thank you
Add Answer to:
Please show all work.
In the circuit shown: Vs = 7 V, Is = -3 mA,...
Question 2 (6 points) D1 lkn Vout The circuit shown has Vs = 10 V. Assume...
Question 2 (6 points) D1 lkn Vout The circuit shown has Vs = 10 V. Assume the diode has Vp = 0.7 V at ID = 2 mA and VI = 25 mV. Use the iterative technique to find the diode current (do two iterations only). Use the diode current found to determine the value of Vout: Vout = 9.300 V Vout = 9.262 V Vout = 9.296 V Vout = 9.189 V
This is a Diode constant voltage model - clipping circuits Please explain steps as you solve....
This is a Diode constant voltage model - clipping
circuits
Please explain steps as you solve. Thank you very much for
your help. please ask if there is anything not clear about the
problem
W (a) For the circuit shown below use the constant voltage diode model (Vp=0.7 V), and find the state of diodes D, and D2 (ie. ON or OFF) and determine the voltage and the current for each. 32k2 OV 5 mA 103=_ ; VD3= 104= ;...
Part IIl: Diodes The Ideal-Diode Model a) For the circuit below, find ID and VD for the case VDD 5 V and R 10 k2. Assum...
Part IIl: Diodes The Ideal-Diode Model a) For the circuit below, find ID and VD for the case VDD 5 V and R 10 k2. Assume that the diode has a voltage of 0.7 V at 1-mA current. Use (a) iteration and (b) the constant-voltage-drop model with VD 0.7 V 홍Yo b) Design the circuit below to provide an output voltage of 2.4 V. Assume that the diodes available have 0.7-V drop at 1 mA. +10 V Vo
Part IIl:...
In this circuit, the source voltage is VS = 25 V, and the resistances are: R1...
In this circuit, the source voltage is VS =
25 V, and the resistances are:
R1 = 10 kΩ, R2 = 18
kΩ,
R3 = 2 kΩ, R4 = 20 kΩ.
Using the mesh current method, find the mesh currents
Ia and Ib (polarities as
marked).
In this circuit, the source voltage is Vs = 25 V, and the resistances are: R1 = 10 k 2, R2 = 18 k22, R3 = 2 k.22, R4 = 20 k 2. Using...
Answer with clear writing please 5. Consider an idealized diode with a reverse saturation current 0.01...
Answer with clear writing please
5. Consider an idealized diode with a reverse saturation current 0.01 mA and an abrupt turn-on voltage of 0.7 V (assume no breakdown and operation away from the knee of the diode curve). For the circuit shown, both resistors are 100 Ω, the constant source is VP-7.0 V, and the time- dependent source is Vs 24 sin() V. Calculate (a) the peak positive voltage V and the associated current through the diode and (b) the...
QUESTION 1 In the diode circuit shown aside, given that V1 = V2 = 2.7 V,...
QUESTION 1 In the diode circuit shown aside, given that V1 = V2 = 2.7 V, R = 1 k12 R2 = 2 kn, R3 = 4k and assuming constant-voltage-drop diode model (Vo = 0.7 V), determine the voltage drop (V) across the resistor R1, if the switch (S) is connected to a. Position 1 b. Position 2 V = Na V2
The circuit shown has four unspecified circuit parameters: vs. R1, R2, and d, where d is...
The circuit shown has four unspecified circuit parameters: vs. R1, R2, and d, where d is the gain of the CCCS. To design this circuit, we must specify the values of these four parameters. The graph shown describes a relationship between the current i and the voltage v. Specify values of vs. Ri, R2, and d that cause the current i and the voltage y to satisfy the relationship described by the graph. Hint: The equation representing the output voltage...
#4 The accompanying circuit shows a 4-resistor biased JFET transistor Determine the values of Rp and Rs so that the Q-point is equal to, VDsq 10 V and IDg 5 mA . For the JFET take IDss = 10 mA...
#4
The accompanying circuit shows a 4-resistor biased JFET transistor Determine the values of Rp and Rs so that the Q-point is equal to, VDsq 10 V and IDg 5 mA . For the JFET take IDss = 10 mA, VP =-5 V and λ 0 . The circuit parameters are, R1-740 k, R2-22 1.85 ka, Rs-85 ㏀ and RL-3.5 ㏀. Take the power supply VDD 24 V 2- Vo R1 Vi R2 Signal generator 4-In reference to the circuit...
Voltage and Current Division For the circuit shown, calculate V. V and Vs when V. =...
Voltage and Current Division For the circuit shown, calculate V. V and Vs when V. = 7 V, R; = 18 2. R2 = 66 2. R3 = 57 2. R4 = 37 and Rs = 332 Express your answer to two significant figures, with appropriate units View Available Hint(s) @? R-180 R2 = 660 + V + 12 0.597 V = 7 V R3 - 570 V 1.89 V R$ = 33 R = 37 Vs + - V4...
Show work for full credit. 3. (20 pts) For the circuit shown below, use super position...
Show work for full credit. 3. (20 pts) For the circuit shown below, use super position to find V, if V24 v, V=17 V.R=1500 0, R-4000 VA due to VINI only V. VA due to VN2 only V. VA due to VINI and VIN V R1 R2 A R1) R2) soted diode n r V1 V2 (VIN1) VIN2) ne (s)
Question 2 (6 points) D1 lkn Vout The circuit shown has Vs = 10 V. Assume the diode has Vp = 0.7 V at ID = 2 mA and VI = 25 mV. Use the iterative technique to find the diode current (do two iterations only). Use the diode current found to determine the value of Vout: Vout = 9.300 V Vout = 9.262 V Vout = 9.296 V Vout = 9.189 V
This is a Diode constant voltage model - clipping
circuits
Please explain steps as you solve. Thank you very much for
your help. please ask if there is anything not clear about the
problem
W (a) For the circuit shown below use the constant voltage diode model (Vp=0.7 V), and find the state of diodes D, and D2 (ie. ON or OFF) and determine the voltage and the current for each. 32k2 OV 5 mA 103=_ ; VD3= 104= ;...
Part IIl: Diodes The Ideal-Diode Model a) For the circuit below, find ID and VD for the case VDD 5 V and R 10 k2. Assume that the diode has a voltage of 0.7 V at 1-mA current. Use (a) iteration and (b) the constant-voltage-drop model with VD 0.7 V 홍Yo b) Design the circuit below to provide an output voltage of 2.4 V. Assume that the diodes available have 0.7-V drop at 1 mA. +10 V Vo
Part IIl:...
In this circuit, the source voltage is VS =
25 V, and the resistances are:
R1 = 10 kΩ, R2 = 18
kΩ,
R3 = 2 kΩ, R4 = 20 kΩ.
Using the mesh current method, find the mesh currents
Ia and Ib (polarities as
marked).
In this circuit, the source voltage is Vs = 25 V, and the resistances are: R1 = 10 k 2, R2 = 18 k22, R3 = 2 k.22, R4 = 20 k 2. Using...
Answer with clear writing please
5. Consider an idealized diode with a reverse saturation current 0.01 mA and an abrupt turn-on voltage of 0.7 V (assume no breakdown and operation away from the knee of the diode curve). For the circuit shown, both resistors are 100 Ω, the constant source is VP-7.0 V, and the time- dependent source is Vs 24 sin() V. Calculate (a) the peak positive voltage V and the associated current through the diode and (b) the...
QUESTION 1 In the diode circuit shown aside, given that V1 = V2 = 2.7 V, R = 1 k12 R2 = 2 kn, R3 = 4k and assuming constant-voltage-drop diode model (Vo = 0.7 V), determine the voltage drop (V) across the resistor R1, if the switch (S) is connected to a. Position 1 b. Position 2 V = Na V2
The circuit shown has four unspecified circuit parameters: vs. R1, R2, and d, where d is the gain of the CCCS. To design this circuit, we must specify the values of these four parameters. The graph shown describes a relationship between the current i and the voltage v. Specify values of vs. Ri, R2, and d that cause the current i and the voltage y to satisfy the relationship described by the graph. Hint: The equation representing the output voltage...
#4
The accompanying circuit shows a 4-resistor biased JFET transistor Determine the values of Rp and Rs so that the Q-point is equal to, VDsq 10 V and IDg 5 mA . For the JFET take IDss = 10 mA, VP =-5 V and λ 0 . The circuit parameters are, R1-740 k, R2-22 1.85 ka, Rs-85 ㏀ and RL-3.5 ㏀. Take the power supply VDD 24 V 2- Vo R1 Vi R2 Signal generator 4-In reference to the circuit...
Voltage and Current Division For the circuit shown, calculate V. V and Vs when V. = 7 V, R; = 18 2. R2 = 66 2. R3 = 57 2. R4 = 37 and Rs = 332 Express your answer to two significant figures, with appropriate units View Available Hint(s) @? R-180 R2 = 660 + V + 12 0.597 V = 7 V R3 - 570 V 1.89 V R$ = 33 R = 37 Vs + - V4...
Show work for full credit. 3. (20 pts) For the circuit shown below, use super position to find V, if V24 v, V=17 V.R=1500 0, R-4000 VA due to VINI only V. VA due to VN2 only V. VA due to VINI and VIN V R1 R2 A R1) R2) soted diode n r V1 V2 (VIN1) VIN2) ne (s)
Most questions answered within 3 hours.
-
A grammar is a 4-tuple G, G = (Ν, Σ, Π, Σ, S) where, Ν is...
asked 28 minutes ago -
In this part, calculate the present values. Use the Excel PV
function to compute the present...
asked 27 minutes ago -
Part 1. Primitive Types, Sorting, Recursion for
Homework.java
a) Implement the static method initializeArray that receives...
asked 1 hour ago -
Using C++, build a sorter that can rank a sequence of numbers in
a descending order....
asked 1 hour ago -
Derive ground state term symbols. Use notation 2S(1/2) for state
2S1/2
a) d5
b) f3
c)...
asked 1 hour ago -
A sample of size 31 will be drawn from a population with mean 39
and standard...
asked 2 hours ago -
What is the effect on the P-value when a test is changed from a
two-tailed hypothesis...
asked 2 hours ago -
I wish to estimate µ, the mean of a population. After I collect
and an-
alyze...
asked 3 hours ago -
At a local university, you poll a group of 115 students and find
that 37 of...
asked 2 hours ago -
Gladstone company tracks the number of units purchased and sold
throughout each accounting period but applies...
asked 2 hours ago -
When determining if a molecule's configuration is E or Z, what
determines the higher priority groups?
asked 2 hours ago -
13. What is the amount
of conversion cost transferred to finished goods? (Round
your intermediate calculations...
asked 2 hours ago