3-F) b. Vout = 0.99 Vin
3-E) For the following circuit, with Ri 18 k2, R2 15 k(2, R6 = 40 kQ, V,-10 V, and V,-7 V, find: 22 k2, R 30 k2, R4 20 kQ, Rs- a) the current through Ri, R3, & R6 b) the voltage across R2, R4, & Rs Rs V, 3-F) For the following circuit, what is Vout in terms of Vin for each case? a) R1-100 ?, R2-1 k(2, and R3 = 1.0 M(2...
1. (15%) Consider the two circuits: (A) Vout (B) Vin - LC 0001 1 - Vout + Vout a. What is Haljw) = Vin for circuit (A)? b. What is lim Haliwą c. What is lim Ha(jw)? HOG HB(jw) = _Vout d. What is Vin for circuit (B)? e. What is Jim He(jw), f. What is lim HB(jw)?
Graph at least two periods of the output Vout when Vin is the
periodic signal 2sen (2πt).
Consider Ri = Rf = 1kΩ, RC = 1 and D1 and D2 as rectifier
diodes.
Rf Ri o Vout Vin o +15V +15V opamp D2 DI opamp U2 U1 -15V -15V
Rf Ri o Vout Vin o +15V +15V opamp D2 DI opamp U2 U1 -15V -15V
Graph at least two periods of the output Vout when Vin is the
periodic signal 2sen (2πt).
Consider Ri = Rf = 1kΩ, RC = 1 and D1 and D2 as rectifier
diodes.
Rf Ri o Vout Vin o +15V +15V opamp D2 DI opamp U2 U1 -15V -15V
Rf Ri o Vout Vin o +15V +15V opamp D2 DI opamp U2 U1 -15V -15V
1. Active Filters Assume R1 = 10kN and R2 = 20KN Vout Figure 1: Question la. (a) (4 points) Find an expression for Vout(t) in terms of vin(t) and system components. - R2 M Lovout Figure 2: Question lb. (b) (4 points) Find an expression for Vout(t) in terms of vin(t) and and system components. - Vout, ZR1 ovouth ER2 A Figure 3: Questions lc and ld. (c) (4 points) Find an expression for Vout(t) in terms of Vin(t) and...
For the circuit of Figure 2 calculate vout if:A. R1= R2=100kW, RL=100 W, and vin= 5V; B. R1= 1kW, R2=0W, RL=1 W, and vin= 43.5V
Assuming that Vin is a 1 Volt amplitude sinusoid at 1000FHz and zero phase, calculate Vout of the following voltage divider: (be sure to rationalize j to the numerator) 0.01 uf AC Voltage vin out 15K out
ideal pamp Pro ble m #5 Vout( Determine H(S)Via(s oVout using Cas the E.E RI ViN R2 R3
1. Find the Vin-Vout transfer characteristic for this circuit over the range of -10V <Vin< 10V + Vzk = 5V VIN V=0.7V Vout Vi= 0.7V Fig :1
RI Power supply to op amp +12 V mind Vout = + 10 V sinewave Vin = + 200 mv sinewave -12 V The non-inverting amplifier is powered + 12 V and -12 V. What would happen to some outputs if the power supplies were +5 V and -5 V? How would these supplies restrict the input voltage range?