Calculate the fatigue stress concentration for a steel filleted shaft that is loaded in bending Given...
A stepped shaft with a ground finish is made of steel with an ultimate tensile strength of 1200 MPa. The shaft is loaded with a fully reversed torque of 20 Nm. Dimensions of the shaft are given below. (5) a) Given the stress concentration for fatigue loading, Kfs 1.3, find the location and magnitude of the maximum stress in the shaft. (14) b) Find the endurance limit, assuming room temperature and a reliability of 99%. (1) c)Will the part have...
A steel shaft in bending has an ultimate strength of 1400 MPa and a shoulder with a filler radius of 0.5 mm connecting an 18 mm diameter with a 19 mm diameter. Estimate the fatigue stress concentration factor, Kf, using Figure 6-20, 0 0.5 1.0 3.0 3.5 4.0 Notch radius r, mm 1.5 2.0 2.5 (1.4 GPa) (1.0) 1.0 Su = 200 kpsi (0.7) 0.8 150 (0.4) 100 0.6 60 Notch sensitivity 9 0.4 Steels Alum, alloy 0.2 0 0...
S = 200 kpsi A steel shaft in bending has an ultimate strength of 690 MPa and a shoulder with a filler radius of 3 mm connecting a 32 mm diameter with a 38 mm diameter. Estimate the fatigue stress concentration factor, Kf, using Figure 6-20. 0 0.5 1.0 3.0 3.5 4.0 1.0 Notch radius r, mm 1.5 2.0 2.5 (1.4 GPa) (1.0) (0.7) 0.8 150 (0.4) 100 0.6 60 Notch sensitivity a 0.4 Steels Alum, alloy 0.2 0 0...
A notched circular shaft shown is subjected to fully reversed
bending. D=12.7mm, d=10.16 mm, and r=0.5mm. The steel material has
the following mechanical and fatigue properties: yield strength
(σ0)=1000 MPa, ultimate strength (σu)=1200 MPa, the fatigue
strength coefficient (σf’)=1600 MPa, the fatigue strength exponent
(b)=-0.1, and the fatigue limit (σe)=400 MPa.
5. (20 pts) A notched circular shaft shown is subjected to fully reversed bending. D-12.7mm, d-10.16 mm, and r-0.5mm. The steel material has the following mechanical and fatigue properties:...
5. (20 pts) A notched circular shaft shown is subjected to fully reversed bending. D-12.7mm, d-10.16 mm, and r-0.5mm. The steel material has the following mechanical and fatigue properties: yield strength (0o)-1000 MPa, ultimate strength (o ) 1200 MPa, the fatigue strength coefficient (σ) 1600 MPa, the fatigue strength exponent (b) 0.1, and the fatigue limit (oe)-400 MPa. a) (10 pts) Determine the fatigue (S-N) curve for the given notched circular shaft under fully reversed bending (computer generated graph is...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20". The shaft transmits a torque to point A of TA = 340 N.m. The shaft is machined from steel with Sy= 420 MPa and Sut = 560 MPa. The fatigue...
A shaft is to be manufactured from a steel having an ultimate tensile strength of 420 MPa, and a yield stress of 305 MPa. The shaft has a solid circular cross section of diameter 50 mm and is subjected to a sinusoidally varying torque ranging from 60 Nm to 130 Nm. It has also been established that the shaft has a fully-corrected endurance limit of 129 MPa and that a torsional fatigue stress concentration factor, kf = 2.1, exists at...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
Please answer A and B.
The rotating solid stedl shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20. The shaft transmits a torque to point A of TA-340 N m. The shaft is machined from steel with Sy- 420 MPa and Sut-560...
A 1020 steel shaft
3. A 1020 steel shaft has a corrected real endurance limit of Se 40 ksi and a tensile strength of Sut 64 ksi. The shaft is loaded in bending and torsion such that Ma 500 lbf.in, and Tm 300 lbf.in, Mm Ta 0. The stress concentration factors were determined to be Kr 2.25, and Kf 1.75. Provided the design engineer choose a diameter of d 1.0 in, determine the factor of safety n of the shaft...