Homework Answers
Add Answer to:
1. Sketch a free body diagram and write the equilibrium equations for each link. Tız is...
For the mechanism Illustrated in Figure 3, draw free body diagrams of the links. Assume all links...
For the mechanism Illustrated in
Figure 3, draw free body diagrams of the links. Assume all links
have mass and that the centers of mass of all links are in the
middle of the links. Assume the center of mass of link 3 is at C.
Write out the equations need to determine all forces and moments.
Assume that there is an applied torque at O2 driving the
mechanism. Do not solve!
α2=0, ω2=60
rad/sec cw, θ2 = 210 deg,...
Kinematics question Please answer ASAP Figure 3 below shows a full free body diagram of a...
Kinematics question
Please answer ASAP
Figure 3 below shows a full free body diagram of a Slider-Crank mechanism. Link 4 is the slider an F that is acting on link 4 is the friction force on the slider. Tz is the input torque of the mechanism. (12 points) CG, o, 01 Figure 3-Slider-Crank Mechanism a) Develop the equations for the forces (in both the x and y-directions) and torques acting on link 4 taking into account the coefficient of friction,...
Requirement: (1) Draw necessary free body diagrams, (2) write necessary equations, and (3) name the adopted...
Requirement: (1) Draw necessary free body diagrams, (2) write necessary equations, and (3) name the adopted principle 3. The mass of block is 10 kg and the horizontal force applied to the block as shown in Figure below is 100 N. The coefficients of kinetic friction between the block and the inclined plane is μ A 0.2. Determine the acceleration of the block and its direction. Draw free body diagram and write the needed equation (25 points) 30P
L0=2 M=3 a)Free-body Diagram for the beam, and TWO useful equilibrium equations b) breakdown for the...
L0=2 M=3
a)Free-body Diagram for the beam, and TWO useful equilibrium
equations
b) breakdown for the beam, into a minimum of 3 cases ,
with
clear indication of either deflections, and slopes (angles) to be
used in following compatibility
equation
c) Write compatibility equation, and values of deflections or
angles as they are obtained from textbook-
formulas
d)Solution for extra-unknown-reaction, including required
algebra in compatibility equation:
e)Solutions for the rest of unknown-reactions, from part d
above-solution and equilibrium equations of...
This assignment pertains to the planar fourbar mechanism illustrated here. Link 1 is the ground l...
This assignment pertains to the planar fourbar mechanism
illustrated here. Link 1 is the ground link and includes points O2
and O4. Link 2 connects points O2 and A. Link 3 is a rigid body
with moving pivots at points A and B, and Point P is another fixed
point on Link 3. Link 4 connects points O4 and B. A 2-D Cartesian
coordinate system is fixed to ground with its origin at O2.
Can you solve all of it...
Please answer all parts of the questions and please try making them clear and easy to understand. CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is support...
Please answer all parts of the questions and please
try making them clear and easy to understand.
CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is supported by a bal-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem? 300 N 400 N i m A) Four forces and two moments B) Six forces C) Five forces D) Four forces and one...
Please help! I need help finding and solving equations of equilibrium to find the max tension in ...
please help! I need help finding and solving equations of
equilibrium to find the max tension in the cables and the angle
that results in the maximum tension, I also have pictures below of
the work I have so far all I really need is equations for the 4
cable part and that's it but I put the whole assignment so you
could see thanks!
Tower Support System Challenge Challenge Scenario: Due to weather conditions, a major communication tower n...
summatize the following info and break them into differeng key points. write them in yojr own...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
For the mechanism Illustrated in
Figure 3, draw free body diagrams of the links. Assume all links
have mass and that the centers of mass of all links are in the
middle of the links. Assume the center of mass of link 3 is at C.
Write out the equations need to determine all forces and moments.
Assume that there is an applied torque at O2 driving the
mechanism. Do not solve!
α2=0, ω2=60
rad/sec cw, θ2 = 210 deg,...
Kinematics question
Please answer ASAP
Figure 3 below shows a full free body diagram of a Slider-Crank mechanism. Link 4 is the slider an F that is acting on link 4 is the friction force on the slider. Tz is the input torque of the mechanism. (12 points) CG, o, 01 Figure 3-Slider-Crank Mechanism a) Develop the equations for the forces (in both the x and y-directions) and torques acting on link 4 taking into account the coefficient of friction,...
Requirement: (1) Draw necessary free body diagrams, (2) write necessary equations, and (3) name the adopted principle 3. The mass of block is 10 kg and the horizontal force applied to the block as shown in Figure below is 100 N. The coefficients of kinetic friction between the block and the inclined plane is μ A 0.2. Determine the acceleration of the block and its direction. Draw free body diagram and write the needed equation (25 points) 30P
L0=2 M=3
a)Free-body Diagram for the beam, and TWO useful equilibrium
equations
b) breakdown for the beam, into a minimum of 3 cases ,
with
clear indication of either deflections, and slopes (angles) to be
used in following compatibility
equation
c) Write compatibility equation, and values of deflections or
angles as they are obtained from textbook-
formulas
d)Solution for extra-unknown-reaction, including required
algebra in compatibility equation:
e)Solutions for the rest of unknown-reactions, from part d
above-solution and equilibrium equations of...
This assignment pertains to the planar fourbar mechanism
illustrated here. Link 1 is the ground link and includes points O2
and O4. Link 2 connects points O2 and A. Link 3 is a rigid body
with moving pivots at points A and B, and Point P is another fixed
point on Link 3. Link 4 connects points O4 and B. A 2-D Cartesian
coordinate system is fixed to ground with its origin at O2.
Can you solve all of it...
Please answer all parts of the questions and please
try making them clear and easy to understand.
CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is supported by a bal-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem? 300 N 400 N i m A) Four forces and two moments B) Six forces C) Five forces D) Four forces and one...
please help! I need help finding and solving equations of
equilibrium to find the max tension in the cables and the angle
that results in the maximum tension, I also have pictures below of
the work I have so far all I really need is equations for the 4
cable part and that's it but I put the whole assignment so you
could see thanks!
Tower Support System Challenge Challenge Scenario: Due to weather conditions, a major communication tower n...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
Most questions answered within 3 hours.
-
Wildhorse Company follows the practice of pricing its inventory
at the lower-of-cost-or-market, on an individual-item
basis....
asked 34 minutes ago -
3. (10 pts) You grow a corn crop that yields 150 bushels ac-1,
with the following...
asked 22 minutes ago -
7. The term Six Sigma refers to:
Select one:
a. The control limits established in a...
asked 32 minutes ago -
For the following reaction: A(g) + 2 B(g) ⇌ 2 C(g) Calculate the
equilibrium constant K...
asked 34 minutes ago -
Which of the following best describes tidal volume? options:
1.The amount of oxygen in the air...
asked 51 minutes ago -
1. Smaller cost distortions occur when the traditional systems'
single indirect-cost rate and the activity-cost-driver rates:...
asked 59 minutes ago -
Using either a FMECA approach or some other appropriate RCA
tool, identify five risk treatment actions...
asked 59 minutes ago -
If for a test the P-value is between 0.0025 and 0.005, what
conclusion can you draw?...
asked 1 hour ago -
Using Python. Write a function clean2(aList) that takes a list
of integers aList as argument, and...
asked 1 hour ago -
Intrapreneurship is defined as the
development of an enterprise culture with an existing (Nandan,
2009). An...
asked 1 hour ago -
QUESTION 1 Tamiflu is a drug used to treat influenza. A study
found that Tamiflu reduced...
asked 1 hour ago -
Which of the following would be less likely to be used to
allocate factory overhead when...
asked 1 hour ago