Design a protocol that could be used to measure Critical power from lactate measurements?
The critical power test is a reliable tool to understand fatigue processes, evaluate human performance and prescribe training as it is able to provide aerobic and anaerobic parameters using a non-invasive method . The produced power is mathematically plotted against the respective exhaustion times to obtain the intensity of “fatigue threshold”, or critical power (CP), above which maximal oxygen uptake is evoked and the amount of work that can be performed above CP
the hyperbolic power-time relationship from the critical power concept aims to determine the highest intensity that may be sustained for a long time without fatigue The point of optimal respiratory efficiency onset of blood lactate accumulation ) and the so called thresholds concepts were also proposed with basis in the steady state phenomenon. Regarding the thresholds concepts, Wasserman and McIlroy proposed that during an incremental cycle ergometer exercise an “anaerobic threshold” may be detected based on the respiratory gas exchange ratio (i.e., the ratio between CO2 production to O2 consumption). The anaerobic threshold detection was originally proposed to avoid exhaustive and potentially dangerous exercise for cardiac patients. According to these authors, this phenomenon is defined as the onset of significant anaerobic metabolism during exercise.
Conversely, Kindermann challenged the concept based on a second exponential rise of the blood lactate concentration during the latter stages of an incremental treadmill exercise. Then, the former concept stated by Wasserman and McIlroy proposed the first elevation of blood lactate (~2 mmol.l−1) concomitantly with a non-linear increase of the ventilation and respiratory quotient, named the “aerobic threshold” (AT). On the other hand, the anaerobic threshold (AT2) was considered the steep part of the exponential rise in blood lactate. The anaerobic threshold concept (i.e., AT2) will be used throughout this review.
In the 3MT and predictive runs, the blood lactate concentrations were determined using the enzymatic method by spectrophotometry Lactate concentration was determined at 340 nm against a calibration curve with 5, 10, 15 and 30 mM standards.. Repeated measures ANOVA and post hoc Newman-Keuls were used to compare the variables of aerobic and anaerobic capacity, mechanical data and acute physiological responses of heart rate (HR F) and peak blood lactate (LAC P) of all the assessment methods used. ..The post-test lactate concentration indicates participation of anaerobic lactic metabolism , which strengthens anaerobic measures, despite not assuring maximal effort.
Design a protocol that could be used to measure Critical power from lactate measurements?
What design features could be used to increase critical mach number of an airplane?
1. Measurement of the lactate threshold has been used to estimate maximal a. aerobic power. b. steady-state running speed. c. performance in events lasting less than 60 seconds. d. power of the ATP-PC system. 2. Which of the following instruments may be used to directly measure lactate accumulation in the blood? a. Blood test b. Direct calorimetry c. Indirect calorimetry d. Saliva test 3. EPOC is largest when… a. The intensity of the exercise is low throughout the session b....
Measurements in the 1800s showed that a draft horse could provide a maximum steady output power over the course of a working day; that's how the "horsepower," about 750 W, came to be defined. Another animal that's used for pulling loads for which there are good data is the sled dog. A 38 kg dog can provide power to pull a sled with a force of 60 N at a steady 2.2 m/s. Dogs and horses have approximately the same...
1. Why are melting point measurements used only to identify organic compounds and not to measure inorganic chemicals? 2. What is Freezing point? Can you give an example in your daily life? What happens when sugar is continuously added into a cup of water? What is the difference if the saturated sugar cup of water is heated? 3.
What are the different types of performance metrics used to measure transportation providers? Could this same list be used for a third party logistics provider? Why or Why not?
1. Power and Work: What units are used to measure power? How would you calculate work from a graph of power vs. time? 2. Energy and Capacitance: How much energy can a capacitor C store at a given voltage? Call this quantity E. How much energy (in terms of E) can the capacitor store if the voltage is doubled? 3. Assume you have just used the energy stored in a capacitor to raise up a mass on a string using...
Assignment 3: EECE 7101 Embedded System Design Design an Arduino based system to measure from – 100V to +100V. Show the design calculations and basic diagram. Consider that the Arduino can convert OV to +5V analog voltage only to digital signal.
Design Problem Design a speed reducer gear box that will take 1.5 kW power from an electric motor rotating at 3000 rpm (clockwise) and deliver it to a machine which operates at 2 different speeds, 1000 rpm (clockwise) and 500 rpm (counter-clockwise). Use Spur Gears with 20° pressure angle and 5mm module. Gear box should be of smallest possible size. The gear shift mechanism is not the part of the design A 2-speed double-reduction speed reducer is shown in the...
Constants Part A A mass spectrograph is used to measure the masses of ions, or to separate ions of different masses. In one design for such an instrument, ions with mass m and charge q are accelerated through a potential difference V. They then enter a uniform magnetic field that is perpendicular to their velocity and are deflected in a semicircular path of radius R. A detector measures where the ions complete the semicircle and from this it is easy...
1. A formula that could be used to measure the force of friction is Ff < mFN. If you were given a force measuring device (e.g., spring scale, force probe) and an object, describe in a few sentences the procedure that one could use to determine the coefficient of static friction. If you were given a force measuring device (e.g., spring scale, force probe) and an object, describe in a few sentences the procedure that one could use to determine...