Homework Answers
Add Answer to:
please write clearly . thank you
The driveshaft of a coast guard vessel is 50 long....
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made...
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degrees over the 36 inches length. The inside diameter of the shaft is 0.65 that of the outside diameter of the shaft. Determine: a) the required inside and outside diameter of the shaft based on...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP at 1250 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 Inche length. The inside diameter of the shaft is 0.8 that of the outside diameter of the shaft. Determine: a) the required inside and...
Please, show all work in a detailed manner. Thanks. Problem #1 The motor shown operates at...
Please, show all work in a detailed manner. Thanks.
Problem #1 The motor shown operates at a steady 500 rpm with a power output of 4 horsepower. The solid shaft has an outer radius of 0.375 in. (1) What is the current magnitude of the maximum shear stress in the shaft? (2) If the shaft is replaced with a hollow shaft of outer radius 0.50 in, what is the smallest wall thickness (t) that will keep the maximum shear stress...
Both parts please Question 1. (a) A steel tube having inner and outer dimeters of 1.5...
Both parts please
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T-524 N-m from the...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rp...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity...
please write some steps
Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
2. Ser A motor with 25 hp at 3000 rpm is connected to a 3 ft...
2. Ser A motor with 25 hp at 3000 rpm is connected to a 3 ft long hollow shaft. The outside diameter is 1" and the wall thickness is 1/8", and the material has an allowable shear stress of 10 ks (35 pts) a) Determine the minimum and maximum shear stress in the shaft b) What is the factor of safety against failure? c) Determine the total angle of twist in the shaft. Bac 3. For the 2D member loaded...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
6 Section 2. Problem 6 (25 pts. A hollow shaft 36 inches long tranmits 105 HP at 1250 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 Inche length. The inside diameter of the shaft is 0.8 that of the outside diameter of the shaft. Determine: a) the required inside and...
Please, show all work in a detailed manner. Thanks.
Problem #1 The motor shown operates at a steady 500 rpm with a power output of 4 horsepower. The solid shaft has an outer radius of 0.375 in. (1) What is the current magnitude of the maximum shear stress in the shaft? (2) If the shaft is replaced with a hollow shaft of outer radius 0.50 in, what is the smallest wall thickness (t) that will keep the maximum shear stress...
Both parts please
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T-524 N-m from the...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
please write some steps
Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
2. Ser A motor with 25 hp at 3000 rpm is connected to a 3 ft long hollow shaft. The outside diameter is 1" and the wall thickness is 1/8", and the material has an allowable shear stress of 10 ks (35 pts) a) Determine the minimum and maximum shear stress in the shaft b) What is the factor of safety against failure? c) Determine the total angle of twist in the shaft. Bac 3. For the 2D member loaded...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
Most questions answered within 3 hours.
-
To get a sample of a certain size, scores are taken one-by-one
from the observed data...
asked 2 minutes ago -
A check-processing center uses exponential smoothing to forecast
the number of incoming checks each month. The...
asked 11 minutes ago -
Teams with high levels of ______ and ______ deal with task
conflict better than those without...
asked 23 minutes ago -
Create a C++ project called lab3b and add the following source
code init_struct.cpp to the project....
asked 34 minutes ago -
12.
A budget that can be easily adjusted to show budgeted revenues,
costs, and cash flows...
asked 42 minutes ago -
________ unemployment changes slowly and depends on
________.
Select one:
a. Frictional; the rate at which...
asked 1 hour ago -
These surveys collect information in low- and
middle-income countries regarding the total fertility rate and the...
asked 1 hour ago -
I need to determine the concentration of hydrogen peroxide in a
solution using titrimetric analysis
25...
asked 1 hour ago -
Your are the Vice-President of operations for a New Orleans food
chain. In the aftermath of...
asked 1 hour ago -
Create a flowchart and a program; test the program. Program
Requirements.
- There are 10 members...
asked 1 hour ago -
Which of the following is not a sensory receptor?
a. a hair cell
b. a rod
c. a...
asked 1 hour ago -
Does the launch speed depend significantly upon the launching
angle? Is it reasonable?
asked 2 hours ago