Homework Answers
Add Answer to:
7. (15 pts) Consider a shaft that is rotating at 150 rpm driving a bevel gear...
For the bevel gear set shown below, shaft AB is rotating at 700 rpm and transmits...
For the bevel gear set shown below, shaft AB is rotating at 700 rpm and transmits 8.5kw, with a 25° pressure angle. 75 mm -165 mm 100 mm 20 mm dia. 75 mm 33 mm 100 mm 28 mm dia. a) Determine the bevel angle y for the pinion on shaft AB and bevel angler for the gear on shaft CD. (8 marks) b) Determine the pitch-line velocity. (4 marks) c) Determine the tangential, radial, and axial forces transmitted through...
A pair of bevel gears is required to transmit 11 kW at 500 r.p.m. from the motor shaft to another...
A pair of bevel gears is required to transmit 11 kW at 500 r.p.m. from the motor shaft to another shaft, the speed reduction being 3 : 1. The shafts are inclined at 60º. The pinion is to have 24 teeth with a pressure angle of 20º and is to be made of cast steel having a static stress of 80 MPa. The gear is to be made of cast iron with a static stress of 55 MPa. The tooth...
A portion of a shaft where a gear is to be mounted has diameter of 50...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power a...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shaft...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
A stepped shaft with a ground finish is made of steel with an ultimate tensile strength of 1200 MPa. The shaft is l...
A stepped shaft with a ground finish is made of steel with an ultimate tensile strength of 1200 MPa. The shaft is loaded with a fully reversed torque of 20 Nm. Dimensions of the shaft are given below. (5) a) Given the stress concentration for fatigue loading, Kfs 1.3, find the location and magnitude of the maximum stress in the shaft. (14) b) Find the endurance limit, assuming room temperature and a reliability of 99%. (1) c)Will the part have...
Q-1 The shaft shown in figure below, supported by and turns in the bearings A and B. The dimensions of the shaft are a = 120 mm and b = 30 mm. The forces on the bevel (conical) gear attached to the sh...
Q-1 The shaft shown in figure below,
supported by and turns in the bearings A and B.
The dimensions of the shaft are a = 120 mm and b =
30 mm. The forces on the bevel (conical) gear attached to the
shaft are Wt = 4500 N, Wr =
2500 N, and Wa = 1000 N. The gear forces act at
a radius R = 100 mm from the shaft axis.
Determine the loads applied to the bearings (FrA...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20". The shaft transmits a torque to point A of TA = 340 N.m. The shaft is machined from steel with Sy= 420 MPa and Sut = 560 MPa. The fatigue...
please solve with details Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered t...
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
The rotating solid steel shaft is simply supported by bearings at points B and C and...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
For the bevel gear set shown below, shaft AB is rotating at 700 rpm and transmits 8.5kw, with a 25° pressure angle. 75 mm -165 mm 100 mm 20 mm dia. 75 mm 33 mm 100 mm 28 mm dia. a) Determine the bevel angle y for the pinion on shaft AB and bevel angler for the gear on shaft CD. (8 marks) b) Determine the pitch-line velocity. (4 marks) c) Determine the tangential, radial, and axial forces transmitted through...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
A stepped shaft with a ground finish is made of steel with an ultimate tensile strength of 1200 MPa. The shaft is loaded with a fully reversed torque of 20 Nm. Dimensions of the shaft are given below. (5) a) Given the stress concentration for fatigue loading, Kfs 1.3, find the location and magnitude of the maximum stress in the shaft. (14) b) Find the endurance limit, assuming room temperature and a reliability of 99%. (1) c)Will the part have...
Q-1 The shaft shown in figure below,
supported by and turns in the bearings A and B.
The dimensions of the shaft are a = 120 mm and b =
30 mm. The forces on the bevel (conical) gear attached to the
shaft are Wt = 4500 N, Wr =
2500 N, and Wa = 1000 N. The gear forces act at
a radius R = 100 mm from the shaft axis.
Determine the loads applied to the bearings (FrA...
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
Most questions answered within 3 hours.
-
Implement the Smith-Waterman algorithm in C that accepts a
substitution matrix.
You may assume the substitution...
asked 1 minute from now -
The equilibrium constant Kp for the reaction
C(s)+H2O(g)⇌CO(g)+H2(g) is 2.44 at 1000 K. What are the...
asked 10 minutes ago -
HACKING
1: Discuss the tricks of hacking in 300 words.
2: Explain in you own words...
asked 11 minutes ago -
Answer the following questions about the NOCl molecule. There
are [?] single bonds in this molecule....
asked 9 minutes ago -
The range of frequencies included in an RF pulse is referred to
as it's bandwidth (BW)....
asked 13 minutes ago -
In the context of the 55 principles, _________
means to keep a process going through training,...
asked 23 minutes ago -
Can you write a 400 words paragraph about investigation on
permeability of cell membrane for SDS,...
asked 23 minutes ago -
This question is regarding Computer Security;
What do you think are some other security risks and...
asked 31 minutes ago -
Assume that you work for an organization that has around 10,000
desktops/laptops and approximately 1,000 servers...
asked 39 minutes ago -
An electron moves along the z-axis with vz=5.2×10^7m/s.
As it passes the origin, what are the...
asked 42 minutes ago -
Silly-Sort(A,i,j)
if A[i] > A[j]
then exchange A[i] and A[j];
if i+1 >= j
then return;...
asked 45 minutes ago -
Discuss the major contributions of Max Weber in understanding
the society theoretically. [10]
asked 48 minutes ago