I started this curcuit and seem to have gotten stuck how do I solve it. Problems:...
Was wondering if someone could show me how
to solve these. I am stuck... :/
FYI, this is linear algebra.
2. (8 points) Let Vị and V2 be the subspaces of R3 given respectively by the equations: V : x1 + 22 + x3 = 0 V2: 2x1 – 22 – x3 = 0 (a) (2 points) Find a basis for Vił. (b) (2 points) Find a basis for Vit. (c) (4 points) Find an orthonormal basis (u1, U2, uz)...
please solve these 2 problems. I will rate you up
In the circuit shown below, let V. - 3 V.1. - 1 mA, R-3k, Ry - 2.5 kA, R = 1 kq Use mesh analysis to find mesh currents I, and 12. Also, find Vı. R1 V1 R2 W 2 is len 3kR 12 R3 100 IMA Problem 5 In the circuit shown below, let V, -8 V, 1. - 2 mA, R2 = 1 k 2, R2 = 400,...
This solution is in the solutions manual, but how do I
solve usit by creating a second order differential
equation?
No energy is stored in the circuit shown in the figure when the
input voltage vg jumps instantaneously from 0 to
25 mV. The initial values of voltage arevo1(0)=5
V and vo(0)=8 V.(Figure 1)
0.1μF 250 kΩ 5 V 500 kΩ #9V 2 Figure 8.19 ▲ liecinouit tier Bh mpl R.13.
Please show me how to solve this first-order circuit. The
answers for the problems are included in the second photo
Problem a. 10-12 50.2 v too 25mH cerere ☺ anv 3002 AWW the The circuit switch is is in closed steady state when at t=o. (a) (b) (c) (d) Find in(t) for all t. Find Uxlt) and Ult) for all t. Sketch inst) and Unlt) for all t. Label an highlight any discontinuities in LLE) and Unlt) at t=0, and...
How do I solve this ?
2. [15 points] For a circuit below, find Voltages and Currents on R1, R2, R3, R4, R5 and R6. Use either Nodal or Mesh Analysis to solve the circuit. Why you choose Nodal or Mesh Analysis? Vi = 20V, V3 = 20V, R;= 1.0 k1, R= 1.2 k1, R;= 4.1 kN, R = 4.1 kN, R=4.2 kN, R=0.5 k12. R3 R1 R4 V1 V2 HE Hilt R2 R5 R6
Hello, could you solve these problems? I hope no mistakes.
1. Find all the currents and voltages in the following circuit. For what values of V(collector voltage of Q2) is I =IREF valid? +6V TREF 32 KN OV -6 V 2. The following circuit shows a common-emitter amplifier with emitter resistances. Vec RCP Vis SR, RE, Rę, = = a) Draw the equivalent small-signal T-model for the circuit. b) Derive an expressions for Rin and Gy= Vo/Vsig (No need for...
will someone please explain fairly thoroughly how to correctly
solve number one? I seem to keep getting the same answer no matter
what i do
1. The 1500 kg steel beam is supported by two ropes as shown below. tension in each cable? -30°.0, -25°. What is the Ticos - (T, sind, cosa = mg yo *T, (0.866) +/T, (0.5)) (0.9063) = 14700 (0.4226) A - T, (0.866) +J, (0.57(0.9063) =6212.45 O T, (0.866 +0.5) = 6854.72 Etx= - Ti...
I need help to know how to solve 5) and 7)
please explain how to solve. thank you
+ V - - V5 + + Vs - Α Ι 2KΩ III, 2ΚΩ + <6ΚΩ 10kΩ DO05 [5] Write down the KVL expressions in terms of Vs, V1, V2, V3, V4, Vs, and Vo for each of the six loops, La, LB, Lc, Lp, LE, and Lf. These loops are shown in the circuit diagram, Figure 3b, above. Start at the...
This is what I have done, but that integral isn't solve-able,
what am I doing wrong?
Compute the weighted surface area Are weighed = 1! (x2 + y){FuxF|| Ilu xlv 'weigthed Of the monkey saddle parameterized by: F(u,v)=(u, v,uº – zuv”) where u’+v’s1 This quantity is also known as the moment of inertia of the surface. Spin that monkey! 215-135(1+5/1) FON, PP309?) - <1,01 302 303 0 uurcoso versine U21 r2 2050 v2 pagine LUXO 30:32 to (-302 +3v1 +...
I have to solve this problem using Kirkhoff's Loop Rule and
Junction rule and I keep getting the wrong answers for the
currents. Thank you for your help.
Find the currents flowing in the circuit in the figure below. (Assume the resistances are R1-20 Ω, R2 = 6 Ω, R,-15 Ω, R4 = 10 Ω, r1-0.75 n, r2 = o.25 n, ra = o.25 Ω. and 40.50 12 = Ro R2 12 V E118 V 24 V