Question

The shaft is made of A-36 steel. It has a diameter of 0.9 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for A- 36 steel is 11 × 103 ksi. (Figure 1) Part A Determine the angle of twist of gear C with respect to B Express your answer using three significant figures. rad Figure 1 of 1 Submit < Return to Assignment Provide Feedback B 60lb-ft 2 ft 60 lb-ft 2.5 ft 3 ft

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Torsion equalion า 6o XI2 Ty 0.94 32 Вс cle 32x60x12x 2.5x12 2 0. 3048 rod

Add a comment
Know the answer?
Add Answer to:
The shaft is made of A-36 steel. It has a diameter of 0.9 in. and is...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • The two shafts are made of A-36 steel. Each has a diameter of 23 mm and...

    The two shafts are made of A-36 steel. Each has a diameter of 23 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by journal bearings at C and D, which allow free rotation of the shafts along their axes. A torque of 500 N·m is applied to the gear at E as shown in the figure below. The shear modulus...

  • The two shafts are made of A-36 steel. Each has a diameter of 23 mm and...

    The two shafts are made of A-36 steel. Each has a diameter of 23 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by journal bearings at C and D, which allow free rotation of the shafts along their axes. A torque of 500 N·m is applied to the gear at E as shown in the figure below. The shear modulus...

  • Alt h. 10- The motor delivers 40 hp to the 304 stainless steel shaft while it...

    Alt h. 10- The motor delivers 40 hp to the 304 stainless steel shaft while it rotates at 20 Hz. The shaft is supported on smooth bearings at A and B, which allow free rotation of the shaft. The gears C and D fixed to the shaft remove 25 hp and 15 hp, respectively. Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is 8 ksi and the allowable angle of twist of...

  • (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

    (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N·m from the engine to the generator. Determine the angle of twist (0) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa.

  • A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made...

    A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degrees over the 36 inches length. The inside diameter of the shaft is 0.65 that of the outside diameter of the shaft. Determine: a) the required inside and outside diameter of the shaft based on...

  • Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm...

    Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm. Assume that the bearings shown allow free rotation of the shafts. If a 400 N-m torque is applied at gear D, determine (a) the maximum shear stress magnitudes in each shaft. (b) the angles of twist ф, and ф (c) the...

  • (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60...

    (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T=524 N·m from the engine to the generator. Determine the angle of twist (%) of the shaft. The shear modulus of elasticity (G) of the shaft material is 75 GPa. (10 points)

  • 75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter...

    75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter shafts are coupled together using the perfectly meshed gears shown. Shaft DC is fixed to the wall at D and supported with a frictionless journal bearing. Shaft EF is supported with two frictionless journal bearings. The modulus of rigidity of steel is 80 GPa. Before the torque is applied, the angle of twist in each shaft is zero, and the angle of rotation of...

  • The 50-mm-diameter shafts AB & DE are made of A-36 steel (G = 75 GPa) and...

    The 50-mm-diameter shafts AB & DE are made of A-36 steel (G = 75 GPa) and are supported on journal bearings that allow the shafts to rotate freely and the turbine at Eis fixed from turning. If the allowable angle of twist of C with respect to Eis 0.2" and shaft AB rotates at 30 Hz, determine the maximum power (hp) that can be delivered from the motor, 0.75 m Tunin

  • Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...

    Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT