Homework Answers
q
Add Answer to:
A plane wall is composed of two materials. Material A has a uniform heat generation of...
A planar wall is composed of two materials, wall 1 has a uniform heat generation of...
A planar wall is composed of two materials, wall 1 has a uniform heat generation of 1.5 x 106 W/m3 and a thermal conductivity of 60 Wm.Κ. Wall 2 has no heat generation and thermal resistance of 150 W/m.K. The inner surface of Wall 1 is well insulated, while the outer surface of Wall 2 is exposed to 30°C fluld. The temperature of the wall surface exposed to the fluid is most nearly 00 heat flow fluid at 30°C h...
4) A 15 cm wall is known to have an internal heat generation rate of 1.7.10...
4) A 15 cm wall is known to have an internal heat generation rate of 1.7.10 . The wall is insulated on its inner surface and exposed to air with properties of To-88℃ and ho 490 W/m2K on its outer surface. The maximum temperature of the wall is found to be equal to 270 °C. a. b. c. Draw the resistance circuit. Determine the thermal conductivity of the wall. Determine the heat flux leaving the wall. enovo
A plane wall of thickness L has constant thermal conductivity, k, uniform generation throughout, q, and...
A plane wall of thickness L has constant thermal conductivity, k, uniform generation throughout, q, and is insulated on one side, at x-0. Only the outer surface temperature (Ts) is known. (a) Derive an equation describing the steady-state wall temperature at any point (x), when given the outer wall surface temperature, Tsi. (b) If L-15 cm, k: 3.4 W/m"K, q-10 kW/m3, and Ts1-300 K, what is the steady-state temperature at x - 6 cm (in K)? S1
Problem 1: (10 points) The composite wall of an oven consists of three materials, two of...
Problem 1: (10 points) The composite wall of an oven consists of three materials, two of which are of known thermal conductivity, k 20 W/mK and ke-50 W/m.K, and known thickness, La 0.30 m and 0.15 m. The third material, B, which is sandwiched between materials A and C is of known thickness, 0.15 m, but unknown thermal conductivity ks. Under steady-state operating conditions, measurements reveal an outer surface temperature of 20°C, an inner surface temperature of T 600°C, and...
Q1) Inner surface of a side wall is used for heating of ambient-room air as shown...
Q1) Inner surface of a side wall is used for heating of ambient-room air as shown below. There is an electrical heater with 10 W/m2 heat flux generation between a layer of insulation and 2 cm thick marble exposed to ambient-room air at T-20 °C with h-20 W/m2K. k-0.04 W/mK Marble with a thickness of 2 cm Ts= 10 ℃ outside Ambient-room air at To Electrical heating layer (negligible thickness) of temperature T-? Insulation with a thickness of 5 cm...
For such aircraft application (Figure 3), a wall is made from insulation material (k-0.030 W/m.K) and...
For such aircraft application (Figure 3), a wall is made from insulation material (k-0.030 W/m.K) and the insulation material is mounted between four layers of carbon steel (2 mm thickness), the carbon layers are separated by a 2 mm air gap (kair-0.025 W/mK). Figure 3, the thermal conductivity of the carbon steel is (k-15.5 W/m.K). The temperature inside the wall is maintained at 6 °C. The environmental temperature is 24°C. The engineer would like to avoid condensation occurring at outer...
The heat generation rate in a plane wall of 0.24 m thickness is 0.4 MW/m3 ....
The heat generation rate in a plane wall of 0.24 m thickness is 0.4 MW/m3 . The wall is exposed on both sides to convection at 30°C. (a) Determine and compare the maximum temperatures for k = 25, k = 50, k = 200 and k = 410 W/mK assuming h = 250 W/m2K. (b) Determine and compare the maximum temperature for h = 50, 250, 500 and 1000 W/m2K with k = 25 W/mK.
A long cylindrical rod of diameter 100 mm with thermal conductivity of 0.5 W/mK experiences uniform...
A long cylindrical rod of diameter 100 mm with thermal conductivity of 0.5 W/mK experiences uniform volumetric heat generation of 5.0 x 10 W/m². The rod is encapsulated by a circular sleeve having an outer diameter of 400 mm and a thermal conductivity of 4 W/mK. The outer surface of the sleeve is exposed to cross flow of air at 27°C with a convection coefficient of 25 W/m2K (a) Find the temperature at the Interface between the rod and sleeve...
Questions 6-9 The walls of a refrigerator are typically constructed by sandwiching a layer of insulation...
Questions 6-9 The walls of a refrigerator are typically constructed by sandwiching a layer of insulation between sheet metal panels. Consider a wall made from fiberglass insulation of thermal conductivity ki = 0.046 W/mK and thickness Li 50 mm and steel panels, each of thermal conductivity kp = 60 W/m. K and thickness Lp = 3 mm. If the wall separates refrigerated air at Too,i = 4°C from ambient air at T0o,0 = 25°C, what is the heat gain per...
Figure 1 A typical section of a building wall is shown in the following figure. This section exte...
Figure 1 A typical section of a building wall is shown in the following figure. This section extends in depth and repeated in vertical direction. The wall support members (grey parts) are made of steel with thermal conductivity of k.-50W/mK and dimensions ofLs-50mm by t23. The remainder of the inner wall space is filled with insulation. The inner wall is made of gypsum board with thermal conductivity of k-0.5W/ mK and thickness of tı2-10mm The inner wall is made of...
A planar wall is composed of two materials, wall 1 has a uniform heat generation of 1.5 x 106 W/m3 and a thermal conductivity of 60 Wm.Κ. Wall 2 has no heat generation and thermal resistance of 150 W/m.K. The inner surface of Wall 1 is well insulated, while the outer surface of Wall 2 is exposed to 30°C fluld. The temperature of the wall surface exposed to the fluid is most nearly 00 heat flow fluid at 30°C h...
4) A 15 cm wall is known to have an internal heat generation rate of 1.7.10 . The wall is insulated on its inner surface and exposed to air with properties of To-88℃ and ho 490 W/m2K on its outer surface. The maximum temperature of the wall is found to be equal to 270 °C. a. b. c. Draw the resistance circuit. Determine the thermal conductivity of the wall. Determine the heat flux leaving the wall. enovo
A plane wall of thickness L has constant thermal conductivity, k, uniform generation throughout, q, and is insulated on one side, at x-0. Only the outer surface temperature (Ts) is known. (a) Derive an equation describing the steady-state wall temperature at any point (x), when given the outer wall surface temperature, Tsi. (b) If L-15 cm, k: 3.4 W/m"K, q-10 kW/m3, and Ts1-300 K, what is the steady-state temperature at x - 6 cm (in K)? S1
Problem 1: (10 points) The composite wall of an oven consists of three materials, two of which are of known thermal conductivity, k 20 W/mK and ke-50 W/m.K, and known thickness, La 0.30 m and 0.15 m. The third material, B, which is sandwiched between materials A and C is of known thickness, 0.15 m, but unknown thermal conductivity ks. Under steady-state operating conditions, measurements reveal an outer surface temperature of 20°C, an inner surface temperature of T 600°C, and...
Q1) Inner surface of a side wall is used for heating of ambient-room air as shown below. There is an electrical heater with 10 W/m2 heat flux generation between a layer of insulation and 2 cm thick marble exposed to ambient-room air at T-20 °C with h-20 W/m2K. k-0.04 W/mK Marble with a thickness of 2 cm Ts= 10 ℃ outside Ambient-room air at To Electrical heating layer (negligible thickness) of temperature T-? Insulation with a thickness of 5 cm...
For such aircraft application (Figure 3), a wall is made from insulation material (k-0.030 W/m.K) and the insulation material is mounted between four layers of carbon steel (2 mm thickness), the carbon layers are separated by a 2 mm air gap (kair-0.025 W/mK). Figure 3, the thermal conductivity of the carbon steel is (k-15.5 W/m.K). The temperature inside the wall is maintained at 6 °C. The environmental temperature is 24°C. The engineer would like to avoid condensation occurring at outer...
A long cylindrical rod of diameter 100 mm with thermal conductivity of 0.5 W/mK experiences uniform volumetric heat generation of 5.0 x 10 W/m². The rod is encapsulated by a circular sleeve having an outer diameter of 400 mm and a thermal conductivity of 4 W/mK. The outer surface of the sleeve is exposed to cross flow of air at 27°C with a convection coefficient of 25 W/m2K (a) Find the temperature at the Interface between the rod and sleeve...
Questions 6-9 The walls of a refrigerator are typically constructed by sandwiching a layer of insulation between sheet metal panels. Consider a wall made from fiberglass insulation of thermal conductivity ki = 0.046 W/mK and thickness Li 50 mm and steel panels, each of thermal conductivity kp = 60 W/m. K and thickness Lp = 3 mm. If the wall separates refrigerated air at Too,i = 4°C from ambient air at T0o,0 = 25°C, what is the heat gain per...
Figure 1 A typical section of a building wall is shown in the following figure. This section extends in depth and repeated in vertical direction. The wall support members (grey parts) are made of steel with thermal conductivity of k.-50W/mK and dimensions ofLs-50mm by t23. The remainder of the inner wall space is filled with insulation. The inner wall is made of gypsum board with thermal conductivity of k-0.5W/ mK and thickness of tı2-10mm The inner wall is made of...
Most questions answered within 3 hours.
-
The average length of time between arrivals at a turnpike
toll-booth is 26 seconds. What is...
asked 1 hour ago -
(a) A piston at 6.1 atm contains a gas that occupies a volume of
3.5 L....
asked 2 hours ago -
Please answer true or false. Words
cannot be changed or added in to make it true...
asked 2 hours ago -
An empty test tube weighs 15.923 grams. Then,
MgCl2•6H2O is added into the test tube. After...
asked 2 hours ago -
Assume memory access is 10 units of time and disk access is
10000 units of time....
asked 3 hours ago -
1. Are all good samples random?
2. Magazines often report surveys giving statistics such as “63%...
asked 3 hours ago -
Under all the various types of market structures, firms
must eventually earn some economic profits for...
asked 3 hours ago -
Consider the following fitness regime for a single locus trait
with two co-dominant alleles: w11 =...
asked 3 hours ago -
A large cable company reports the following.
80% of its customers subscribe to its cable TV...
asked 3 hours ago -
Please answer the question in brief.
Discuss the role of ERP in organizations. Are ERP tools...
asked 3 hours ago -
Discuss the pros and cons of collaborative software such
as SameTime. Does it increase productivity? What...
asked 3 hours ago -
Buying your in-laws a gift because it’s expected is
due to the ____________ motive of gift-giving....
asked 3 hours ago