TOIMII. (10 points) Compute V. for the sections shown. Use fc' = 4,000 psi and fy=...
Problem 2 (25 points) A rectangular reinforced concrete beam has a width b-15 inches and effecti Concrete com ve depth d-24 inches. orcement fy- 60 ksi. imate load - 6 k/R pressive strength fe -4,000 psi and yield stress of steel reinf The beam is simply supported and subjected to a uniformly distributed ulti that includes the weight of the beam. Span is 28 feet. Assume interior exposure. s and show the proposed shear reinforcement Design the beam for shear...
Problem 4 Load and Load Combinations (50pts) With fy 60,000 psi and fc' 4000 psi, select the tensile reinforcing for the edge L beam AB for the floor system shown in Figure 4.1. The cross section of the floor system is shown in Figure 4.2. Note that LI = 6ft and L2 = 12ft. Assume simple supports at sides A and B. The live load is to be 80 psf, while the dead load in addition to the concrete's weight...
ZOOM+ Draw shear force diagram [V/6) of the beam shown below Choose No. 3 stirrups and calculate the ACI code-cmplying spacings. 4500 psi; fyt 40 ksi. D = 1.8 kips/ft L 1.4 kips/ft 17.5 14 25 ft Draw shear force diagram 〔V ofthe beam shown below Choose No. 3 stirrups and calculate the ACI code-cmplying spacings. 4000 psi ; fyt-40 ksi. D 1.5 kips/ft L1.8 kips/ft 17.5 22 ft 20 20
Question 1: Calculate Ig and Icr for cross sections (a) and (b) shown in Figure (1). Given: fc=4,000 psi, Normal-Weight Concrete fy=60,000 psi, and Es 29 X 105 psi. 30 in. (762 mm) 3 in. 3 No. 10 3 No, 9 2을 in. 12 in. (304,8 mm) in. -10 in.- (b) (a) 15 in. (wu (533.4 mm) Question 1: Calculate Ig and Icr for cross sections (a) and (b) shown in Figure (1). Given: fc=4,000 psi, Normal-Weight Concrete fy=60,000 psi,...
A reinforced concrete beam shown in Figure below is 15-in. wide and has effective depth of31 in. The factored loads are shown. (The factored uniform load includes the weight of the beam). Design the web reinforcement using the Vu diagram shown in the Figure (for a symmetric half). Assume No. 3 stirrups,fc '-4000 psi and fy=fyt-60000psi. 100 kip 100 kip d-31 in. 15 ft clear span As s) 102.5 kip se 2.5 ki @y、阪、もw cl.* 3..-K: ps A reinforced concrete...
1. A rectangular beam with b 16 in., d-17 in., and h 20 in. has a clear span of 24 ft. as shown below. The beam has 1 ft. of bearing at each end, so for analysis purposes it is treated as a 25 ft. simple span (to center of bearing at each end). The beam supports an unfactored concentrated live load of P-65 kips. The beam is reinforced with 6-#10 longitudinal bars and #4 stirrups. Material strengths are fc-4,000,...
Concrete design Problem #2: Determine the appropriate shear reinforcement required for the beam shown (spacing of stirrups). Do not consider different loading cases for live loads and the dead load shown includes the beam's weight. Assumere 4000 psi, fy-60000 psi, and use # 3 U-shaped stirrups Note: Divide the beam into segments, 36" each where appropriate. 20k () 30k(L) 0-4 255 sy 5 #10
For the beam shown use f-3000 psi and fy 60000 psi. 1- Compute the effective flange width 2- Compute фМ, for the positive and negative moment regions and check ACI requirements for both sections. At the support, the bottom bars are in one layer and at mid-span, the # 8 bars are in the bottom layer and the # 7 bars are in a second layer. Assume 2.5 in concrete cover (from outside face of concrete to the center of...
2.5" 2#7 fc= 4,000 psi fy= 60,000 psi n 8 5#11 3" 18" For service level moment M= 200 ft-k, use the procedures from Chapter 2 to find (20 pts) the following using linear-elastic analysis procedures and using transformed section a. properties: compressive stress in the concrete (fc) tension stress in the bottom steel (fs) compressive stress in the top steel (f's) What is the applicable moment of inertia of the concrete section if the (10 pts) service level moment...
4. Determine the flexural strength (фМп) and shear strength (OVn) of the given section below. The RC beam in Engineering Building is reinforced with 4#10 for tensile reinforcement at the bottom, 2#4 for compressive reinforcement at the top, and stirrups with #3@ 9" on center. (fc 6 ksi, fy 60 ksi for top and bottom reinforcement, and fyt -40 ksi for stirrups): Case 1: t- 3 in (20 points) and Case 2: t- 10 in (20 points) . 14" 6...