Homework Answers
Add Answer to:
Concrete design
Problem #2: Determine the appropriate shear reinforcement required for the beam shown (spacing of...
M 3: (20 points) Design the stirrup spacing for the beam shown below. Change your design between ...
m 3: (20 points) Design the stirrup spacing for the beam shown below. Change your design between Zones 1, 2, and 3 of the beam length, using a uniform spacing in each zone. Ignore the self-weight of the beam. Loads on the beam are service loads so load factors must be applied according to ACI 318 (subscripts "d" and T" denote dead and live loads, respectively). Material strengths are fe 4,0oo psi and fy 60,000 psi. The total factored shear...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension is given. The service loads are 150 psf dead load (doesn't include the beam weight) and 350 psf live load. The beam is on a simple span of 20 ft. Use f:=4000 psi for strength concrete and fy=60000 psi for steel reinforcement. 8-0* (typ.)
A reinforced concrete beam shown in Figure below is 15-in. wide and has effective depth of31 in. ...
A reinforced concrete beam shown in Figure below is 15-in. wide and has effective depth of31 in. The factored loads are shown. (The factored uniform load includes the weight of the beam). Design the web reinforcement using the Vu diagram shown in the Figure (for a symmetric half). Assume No. 3 stirrups,fc '-4000 psi and fy=fyt-60000psi. 100 kip 100 kip d-31 in. 15 ft clear span As s) 102.5 kip se 2.5 ki @y、阪、もw cl.* 3..-K: ps
A reinforced concrete...
The simply supported beam shown spans 20 ft and, in addition to its own weight carries...
The simply supported beam shown spans 20 ft and, in addition to its own weight carries a uniformly distributed service dead load of 1.75 kips/ft and a uniformly distributed live load of 3.0 kips/ft. Five no. 9 bars running the full length of the beam arc used as flexural reinforcement. Assume f,-60,000 psi and fc4000 psi, No. 3 stirrups are used. a. Determine the theoretical spacing of stirrups at the critical section using the detailed expression for the shear strength...
For the simply supported beam shown, the span is 40 ft, dead load including own weight...
For the simply supported beam shown, the span is 40 ft, dead load including own weight is 5 k/ft and live load is 4 k/ft. Assume fy-60,000 psi and fc 4000 psi, find: Size of the longitudinal reinforcement at the critical section (5 points) Spacing of U stirrups # 4 at the critical section (support width is 12 in.) (5 points) a. b. 48" 26.5" As 16
A rectangular beam having b=16 in and d=26 in spans 28 ft face to face of...
A rectangular beam having b=16 in and d=26 in spans 28 ft face
to face of simple supports. It is reinforced for flexure with 6#11
bars that continue uninterrupted to the ends of the span. It is to
carry service dead load 2.0 kips/ft (including self weight) and
service live load 3.6 kips/ft, both uniformly distributed along the
span. Design the shear reinforcement using vertical U stirrups.
Economize the spacing of stirrups in appropriate number of bands.
Material strengths are...
Please answer question 1 thank you Reinforced Concrete HW 18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12...
Please answer question 1 thank you
Reinforced Concrete HW
18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
Please answer question 1 thank you Reinforced Concrete HW 18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12...
Please answer question 1 thank you
Reinforced Concrete HW
18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
The T-beam shown in Figure 1 supports the un-factored dead load of 1.4 kips/ft and live...
The T-beam shown in Figure 1 supports the un-factored dead load
of 1.4 kips/ft and live load of 1.5 kips/ft. The dead load does not
include the self-weight of the beam. The material properties are as
follows: fc’=3000 psi; fy=60,000 psi. Design the shear
reinforcement (stirrups). Plot the stirrups distribution along the
span of the beam.
DL= 1.4 kips/ft ; L2=1.5 kips/Ft * 75 Sz=7 X * b=3616. hr-6in k ) انا امه hw-lain + * bw=12 in
. Deisgn a reinforced concrete cross-section with unknown dimensions Problem 1 Design the steel reinforcement for...
. Deisgn a reinforced concrete cross-section with unknown dimensions Problem 1 Design the steel reinforcement for the beam shown in Figure 1 that supports its own self-weight, a uninformly distributed dead load, a uniformly distributed live load, and a live point load located at midspan. In your solution, you should select the area of reinforcement, the number and size of reinforcing bars, and the section depth in order to receive full credit. Assume J 5,000 psi, fy 60,000 psi. 16...
m 3: (20 points) Design the stirrup spacing for the beam shown below. Change your design between Zones 1, 2, and 3 of the beam length, using a uniform spacing in each zone. Ignore the self-weight of the beam. Loads on the beam are service loads so load factors must be applied according to ACI 318 (subscripts "d" and T" denote dead and live loads, respectively). Material strengths are fe 4,0oo psi and fy 60,000 psi. The total factored shear...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension is given. The service loads are 150 psf dead load (doesn't include the beam weight) and 350 psf live load. The beam is on a simple span of 20 ft. Use f:=4000 psi for strength concrete and fy=60000 psi for steel reinforcement. 8-0* (typ.)
A reinforced concrete beam shown in Figure below is 15-in. wide and has effective depth of31 in. The factored loads are shown. (The factored uniform load includes the weight of the beam). Design the web reinforcement using the Vu diagram shown in the Figure (for a symmetric half). Assume No. 3 stirrups,fc '-4000 psi and fy=fyt-60000psi. 100 kip 100 kip d-31 in. 15 ft clear span As s) 102.5 kip se 2.5 ki @y、阪、もw cl.* 3..-K: ps
A reinforced concrete...
The simply supported beam shown spans 20 ft and, in addition to its own weight carries a uniformly distributed service dead load of 1.75 kips/ft and a uniformly distributed live load of 3.0 kips/ft. Five no. 9 bars running the full length of the beam arc used as flexural reinforcement. Assume f,-60,000 psi and fc4000 psi, No. 3 stirrups are used. a. Determine the theoretical spacing of stirrups at the critical section using the detailed expression for the shear strength...
For the simply supported beam shown, the span is 40 ft, dead load including own weight is 5 k/ft and live load is 4 k/ft. Assume fy-60,000 psi and fc 4000 psi, find: Size of the longitudinal reinforcement at the critical section (5 points) Spacing of U stirrups # 4 at the critical section (support width is 12 in.) (5 points) a. b. 48" 26.5" As 16
A rectangular beam having b=16 in and d=26 in spans 28 ft face
to face of simple supports. It is reinforced for flexure with 6#11
bars that continue uninterrupted to the ends of the span. It is to
carry service dead load 2.0 kips/ft (including self weight) and
service live load 3.6 kips/ft, both uniformly distributed along the
span. Design the shear reinforcement using vertical U stirrups.
Economize the spacing of stirrups in appropriate number of bands.
Material strengths are...
Please answer question 1 thank you
Reinforced Concrete HW
18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
Please answer question 1 thank you
Reinforced Concrete HW
18%20(2).pdf CEE433- Homework Assignment 9 Assigned: 12 April 2018 Due: 19 April 2018 1. Design the shear reinforcement (vertical stirrups) for the beam shown in the figure. Design stirrups based on the shear envelope using the approximate procedure discussed in class. Note that for the overhangs the maximum shear at the support is induced by placing dead and live loads throughout the cantilever portion. Satisfy all strength and spacing requirements specified...
The T-beam shown in Figure 1 supports the un-factored dead load
of 1.4 kips/ft and live load of 1.5 kips/ft. The dead load does not
include the self-weight of the beam. The material properties are as
follows: fc’=3000 psi; fy=60,000 psi. Design the shear
reinforcement (stirrups). Plot the stirrups distribution along the
span of the beam.
DL= 1.4 kips/ft ; L2=1.5 kips/Ft * 75 Sz=7 X * b=3616. hr-6in k ) انا امه hw-lain + * bw=12 in
. Deisgn a reinforced concrete cross-section with unknown dimensions Problem 1 Design the steel reinforcement for the beam shown in Figure 1 that supports its own self-weight, a uninformly distributed dead load, a uniformly distributed live load, and a live point load located at midspan. In your solution, you should select the area of reinforcement, the number and size of reinforcing bars, and the section depth in order to receive full credit. Assume J 5,000 psi, fy 60,000 psi. 16...
Most questions answered within 3 hours.
-
For Dijkstra’s shortest path algorithm:
a. Give the Big-O time for Dijkstra’s shortest path algorithm
and...
asked 4 minutes ago -
Phosphorus violates the 'octet rule' in biological molecules,
forming more covalent bonds than expected based on...
asked 7 minutes ago -
A 1.3 eV electron has a 10-4 probability of tunneling
through a 2.4 eV potential barrier....
asked 25 minutes ago -
What is the one ingredient that is common to being successful
with all stakeholders?
profit
trust...
asked 24 minutes ago -
Write an assembly language 32 bit program that reads in lines of
text by a .txt...
asked 27 minutes ago -
what is the density ( in g/L) of hydrogen gas at 29 degrees C and a...
asked 36 minutes ago -
5-6. You are considering three investment alternatives for some
spare cash: Old Reliable Corporation stock (A1),...
asked 27 minutes ago -
Problem 16-02
Receivables Investment
Medwig Corporation has a DSO of 45 days. The company averages
$7,250...
asked 42 minutes ago -
Mr. Brown hired Lowe's Maintenance Services Limited to repair
and paint the exterior wall of his...
asked 43 minutes ago -
When might an index slow down the overall performance of the
database? Choose the best answer....
asked 48 minutes ago -
Due to a recession, expected inflation this year is only 2.25%.
However, the inflation rate in...
asked 49 minutes ago -
Write four functions: (IN PYTHON 3)
1) bound(l) - given a list of integers l, compute...
asked 52 minutes ago