Hi everyone, I have an very urgent question with calculating transfer function in MATLAB.(I have a test in hours)
Please help me with it.Thanks a lot.
Background:
Question:
Thank you very much.
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Hi everyone, I have an very urgent question with calculating transfer function in MATLAB.(I have a...
This filter is an active bandpass filter Compute the transfer function for the circuit of in terms of the circuit constants R1 R2 R3 C1 and C2. Then, replace the complex variable with omega, and the circuit constants with their numerical values and plot the magnitude versus radian frequency . What kind of filter is this? Find the transfer function of the circuit and Use MATLAB to plot IVout/Vin over frequency to verify your answer. 0.01 μF 106.1 kΩ 0...
1. Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute the center frequency, Wo. Calculate the cutoff frequencies Wej and Wc2, the bandwidth ß, and quality factor, Q. Compute values for R and L to yield a bandpass filter with a center frequency of 5kHz and a bandwidth of 200Hz, using a 10nF capacitor. (25 points) 1. Design a parallel RLC bandpass filter, derive the transfer function H(s). Compute the center frequency, Wo. Calculate the cutoff frequencies...
Hi everyone, I have a question about active filter, including a simulation, Please provide the screen capture. Thanks. 5. Active Filter - III Consider the RC op-amp circuit shown in Fig. 5.4. Vin(t) is a sinusoidal signal with Vpp = 1 V, Rı = 10 ㏀ , R, = 20 ㏀ , and C,-C,-0.01 μF. Use Vcc-15V, The capacitors have zero initial energy stored. Ri 741 C1 C2 Volt) Fig. 5.5: Active filter - III (a) Find the transfer function...
Using Matlab, plot the magnitude and phase of the transfer function (vo/vi) vs. frequency range 1-100 kHz. Use log scale for the frequency axis, dB scale for the magnitude axis, and degrees for the phase axis. Note dB = 20log10(vo/vi). The 10 stands for base 10. I need help writing a MATLAB code to output this plot and also coming up with the vo/vi function itself. 0.1807 H 1402 nF 0.1624 H 1.560nF 1.559 mH
BPF Filter Bandpass Filter The following circuit acts as a C This filter has a center (resonance) frequency at Hz. 27-VLC and a 3-dB bandwidth of BW = Hz. 2RC 3l f, and a passband for which the signal is This means that the filter has 0 dB gain at attenuated less than 3 dB centered approximately at f, from f,-BW2 to f.+BW/2 (this passband is not exactly centered at f, but its total width is BW) 3l8 Input Signal...
21 Vi Z2 Vo Figure 1 1. Ref: Figure 1. Let Z1 L (an inductor), Z2 - R (a resistor). Vi Calculate the magnitude and phase of the transfer function H(w) Figure 1 T 2. Repeat #1 with L = 100 mH, R 1kΩ. a) Plot the frequency response in dB* on a both on a linear scale and then a log scale from ω-1 to 100,000,000 rad/sec with points every decade (1 b) 1,000 etc). 10 100 Plot the...
Find the transfer function H(jω) for the circuit above as a function of jω. (Leave R and L as variables). Assume V R to be the output and V S to be the input. С L RVR(t) vs (t) A. Find the transfer function H(jo) for the circuit above as a function of jaw. (Leave R and L as variables). Assume V to be the output and V to be the input. S R B. Find the Magnitude and Phase...
the circuit shown, 1. Find the transfer function H(jw) 2. If R R2 12 and L1mH, plot the frequency response (both the gain and the phase shift) of the circuit; 3. Identify the type of filter the circuit is, and state the break (cut off) frequency. R1 v(t)Vcos(ut) L1 R2 Figure 1 the circuit shown, 1. Find the transfer function H(jw) 2. If R R2 12 and L1mH, plot the frequency response (both the gain and the phase shift) of...
Styles Paragraph 6. Given the difference equation y(n)-x(n-1)-0.75y(n-1)-0.125(n-2) a. Use MATLAB function filterl) and filticl) to calculate the system response y(n)for n 0, 1, 2, 3, 4 with the input of x(n (0.5) u(n)and initial conditions x(-1)--1, y(-2) -2, and y(-1)-1 b. Use MATLAB function filter!) to calculate the system response y(n) for n-0, 1, 2, 3,4 with the input of x(n) (0.5)"u(n)and zero initial conditions x(-1)-0, (-2)-0, and y(-1)-0 Design a 5-tap FIR low pass filter with a cutoff...
Consider a negative feedback system whose open-loop transfer function is: G(s)H(s)=K/(s(s+1)) Write a MATLAB program to obtain the root-locus plot of G(s)H(s). [2 marks] What are the locations of poles when K = 0.19. [2 marks] When K = 0.4, what are the locations of poles? [3 marks] Find values of the damping ratio, % overshoot and frequency when K = 0.4. [3 marks] Write a MATLAB program to obtain a bode plot of G(s)H(s) when K = 1. [2...