A 2.8-kg disk is constrained horizontally but is free to move vertically. The disk is struck from below by a vertical jet of water. The speed and diameter of the water jet are 12 m/s and 25 mm at the nozzle exit. (a) Obtain a general expression for the speed of the water jet as a function of height, h. (b) Find the height to which the disk will rise and remain stationary.
Homework Answers
Add Answer to:
A 2.8-kg disk is constrained horizontally but is free to move
vertically. The disk is struck...
Problem 6.031 A cone that is held stable by a wire is free to move in...
Problem 6.031 A cone that is held stable by a wire is free to move in the vertical direction and has a jet of water (at 10°C) striking it from below. The cone weighs 30 N. The initial speed of the jet as it comes from the orifice is 35 m/s, and the initial jet diameter is 2 cm. Find the height to which the cone will rise and remain stationary. Note: The wire is only for stability and should...
* * * FIVE STAR * * 1. A projectile of mass 0.30 kg moving horizontally...
* * * FIVE STAR * * 1. A projectile of mass 0.30 kg moving horizontally with speed 20 m/s strikes a stationary mass (3.8 kg) suspended by strings. Subsequently, the masses rise to a height of H. What is the final height H? (see lecture note chapter 7)
Question 2 (6 marks) A vane with an angle of 30° is attached to a cart...
Question 2 (6 marks) A vane with an angle of 30° is attached to a cart (Figure 2). The cart and vane (mass of 75 kg) move on a level track with a constant speed of 10 m/s. The vane receives a jet of water (p = 1000 kg/m) that leaves a stationary nozzle with speed of 35 m/s. The nozzle exit area is 0.003 m². Assume that this cross-sectional area of the water stream does not change as it...
Water (p = 1,000 kg/m?) flows steadily through a 90° elbow and exits as a free...
Water (p = 1,000 kg/m?) flows steadily through a 90° elbow and exits as a free jet through a nozzle, as shown below. The measured upstream gage pressure is 800 kPa. Neglect body forces and viscous effects, and disregard the height of the elbow/nozzle combination. The water velocity at any cross section is assumed to be uniform. However, the water velocity inside the elbow is not negligible compared to that in the nozzle. Consider the following: Determine the velocities V,...
Problem 14.47) Disks A, B, C, and D can ślide freely on a frictionless horizontal surface. Disks B, C, and D are connected by light rods and are at rest in the position shown when disk B is str...
Problem 14.47) Disks A, B, C, and D can ślide freely on a frictionless horizontal surface. Disks B, C, and D are connected by light rods and are at rest in the position shown when disk B is struck squarely by disk A which is moving to the right with a velocity vo 12 m/s. The masses of the disks are m,-m,-mc - 7.5 kg, and m 15 kg. Knowing that after impact disks A and B are bound togetherV)...
V cart Nozzle V. jet- 4. (20 pts) A 3-cm-diameter water jet moving at 40 m/s...
V cart Nozzle V. jet- 4. (20 pts) A 3-cm-diameter water jet moving at 40 m/s velocity in x-direction strikes the vertical back surface of a cart moving horizontally at a constant speed of 10 m/s in the flow direction. After the strike, the water stream splatters off in all directions in the plane of the back surface. Using the moving control volume indicated with dashed lines in the figure, determine: Waterjeti F. Rx X a) The relative velocity and...
A 0.00600 kg bullet traveling horizontally with speed 1.00 103 m/s strikes a 20.8 kg door, embedding itself 11.0 cm from the side opposite the hinges. The 1.00 m wide door is free to swing on its frictionless hinges.
A 0.00600 kg bullet traveling horizontally with speed 1.00 103 m/s strikes a 20.8 kg door, embedding itself 11.0 cm from the side opposite the hinges as shown in the figure below. The 1.00 m wide door is free to swing on its frictionless hinges.What is the angular momentum? At what angular speed (rad/s) does the door swing open immediately after the collision? Calculate the total energy of the bullet-door system and determine whether it is less than or equal...
Problem 1: A car of mass 1000 kg moves at a constant speed of 20 m/s...
Problem 1: A car of mass 1000 kg moves at a constant speed of 20 m/s along a horizontal road where a frictional force is 200N. Calculate the power developed by the engine. If the car now moves up an incline at the same constant speed, calculate the new power developed by the engine. Assume that the frictional force is still 200 N and that sin(theta)=1/20 where theta is the angle of the incline to the horizontal. Problem 2: An...
PLEASE EXPLAIN ALL ANSWERS 3 kg vertically cing is 10 kg g is used to frictionless...
PLEASE EXPLAIN ALL ANSWERS
3 kg vertically cing is 10 kg g is used to frictionless maximum these ag is most 11. Three blocks, A, B, and C. of masses 1, 2, and 3 kg, respectively, are initially at rest on a frictionless surface as indicated in the figure above. What force has to be applied on block C 5= 200 mis? to accelerate the three blocks at 2 m/s? (A) 0.33 N (2) +22) 4362) 16 V=20mis (B) 1.5...
Objective To determine the force generated by a jet of water striking on a surface Description...
Objective To determine the force generated by a jet of water striking on a surface Description of apparatus The supply is led to a vertical pipe terminating in a tapered nozzle. This produces a jet of water which impinges on the vane in the form of a Flat Plate, Hemispherical Cup, Conical Plate or 30° Angled Plate. The nozzle and vane are contained within a transparent cylinder; at the base of the cylinder there is an outlet by which the...
Problem 6.031 A cone that is held stable by a wire is free to move in the vertical direction and has a jet of water (at 10°C) striking it from below. The cone weighs 30 N. The initial speed of the jet as it comes from the orifice is 35 m/s, and the initial jet diameter is 2 cm. Find the height to which the cone will rise and remain stationary. Note: The wire is only for stability and should...
* * * FIVE STAR * * 1. A projectile of mass 0.30 kg moving horizontally with speed 20 m/s strikes a stationary mass (3.8 kg) suspended by strings. Subsequently, the masses rise to a height of H. What is the final height H? (see lecture note chapter 7)
Question 2 (6 marks) A vane with an angle of 30° is attached to a cart (Figure 2). The cart and vane (mass of 75 kg) move on a level track with a constant speed of 10 m/s. The vane receives a jet of water (p = 1000 kg/m) that leaves a stationary nozzle with speed of 35 m/s. The nozzle exit area is 0.003 m². Assume that this cross-sectional area of the water stream does not change as it...
Water (p = 1,000 kg/m?) flows steadily through a 90° elbow and exits as a free jet through a nozzle, as shown below. The measured upstream gage pressure is 800 kPa. Neglect body forces and viscous effects, and disregard the height of the elbow/nozzle combination. The water velocity at any cross section is assumed to be uniform. However, the water velocity inside the elbow is not negligible compared to that in the nozzle. Consider the following: Determine the velocities V,...
Problem 14.47) Disks A, B, C, and D can ślide freely on a frictionless horizontal surface. Disks B, C, and D are connected by light rods and are at rest in the position shown when disk B is struck squarely by disk A which is moving to the right with a velocity vo 12 m/s. The masses of the disks are m,-m,-mc - 7.5 kg, and m 15 kg. Knowing that after impact disks A and B are bound togetherV)...
V cart Nozzle V. jet- 4. (20 pts) A 3-cm-diameter water jet moving at 40 m/s velocity in x-direction strikes the vertical back surface of a cart moving horizontally at a constant speed of 10 m/s in the flow direction. After the strike, the water stream splatters off in all directions in the plane of the back surface. Using the moving control volume indicated with dashed lines in the figure, determine: Waterjeti F. Rx X a) The relative velocity and...
Problem 1: A car of mass 1000 kg moves at a constant speed of 20 m/s along a horizontal road where a frictional force is 200N. Calculate the power developed by the engine. If the car now moves up an incline at the same constant speed, calculate the new power developed by the engine. Assume that the frictional force is still 200 N and that sin(theta)=1/20 where theta is the angle of the incline to the horizontal. Problem 2: An...
PLEASE EXPLAIN ALL ANSWERS
3 kg vertically cing is 10 kg g is used to frictionless maximum these ag is most 11. Three blocks, A, B, and C. of masses 1, 2, and 3 kg, respectively, are initially at rest on a frictionless surface as indicated in the figure above. What force has to be applied on block C 5= 200 mis? to accelerate the three blocks at 2 m/s? (A) 0.33 N (2) +22) 4362) 16 V=20mis (B) 1.5...
Objective To determine the force generated by a jet of water striking on a surface Description of apparatus The supply is led to a vertical pipe terminating in a tapered nozzle. This produces a jet of water which impinges on the vane in the form of a Flat Plate, Hemispherical Cup, Conical Plate or 30° Angled Plate. The nozzle and vane are contained within a transparent cylinder; at the base of the cylinder there is an outlet by which the...
Most questions answered within 3 hours.
-
Calculate the pH of each of the following solutions.
0.50 M HBr
3.1×10−4 M KOH
4.2×10−5...
asked 2 hours ago -
For the year ended December 31, Depot Max’s cost of merchandise
sold was $85,600. Inventory at the...
asked 2 hours ago -
Week 10 - Professional Memo Assignment
Professional Memo Assignment
Your mission for this week, should you...
asked 2 hours ago -
Write a Python program that stores the data for each
player on the team, and it...
asked 2 hours ago -
In
the last 3 months, mike never knows when he is going to get his
allowance...
asked 3 hours ago -
Is Ca(OH)2 a Bronsted base, Lewis base, or both? Why?
asked 3 hours ago -
1A- Why don’t voters complain about U.S. tariffs on imported
sugar?
Because sugar is only a...
asked 3 hours ago -
Cash Payback Period
Primera Banco is evaluating two capital investment proposals for
a drive-up ATM kiosk,...
asked 3 hours ago -
Create a button in Swift (Xcode) that will create a charge,
create a charge using Stripe's...
asked 3 hours ago -
The reaction rate of CO and NO2 in the reaction
CO(g) + NO2(g) → CO2(g) +...
asked 3 hours ago -
Imagine that a chemist puts 6.40 mol each of
C3H8 and O2 in a 1.00-L container...
asked 3 hours ago -
How much money should be invested today in order to have $8340
at the end of...
asked 3 hours ago