if
you have any doubt please post it
QUESTION 7 Imam_Lama | R2 C2 + R33 Given V=8V, I=4A, R1=4ohm, R2=2ohm, R3=3ohm, L1=14mH, L2=17mH,...
Find The values, C1, C2, L1, L2, R1, R2, R3. The tweeter speaker can reproduce frequencies greater than 6kHz, and the woofer can reproduce frequencies less than 200Hz. For proper sound, the midrange should reproduce all frequencies not produced by the subwoofer or tweeter. C2 C1 L2 V1 L1 R1 R3 R2 Midrange Tweeter Woofer Fig. 2. Equivalent model. The values of Ri, R2, R3, L1, L2, G. and C, are selected so that the filters have the same cutoff...
Question 7 R2 C1 1. 3R1 L1 R3 FIGURE LINK For the circuit shown above, calculate the energy stored in the inductor L1. Assume 11 = 24 A, R1 = 16 Ohms, R2 = 21 Ohms, R3 = 35 Ohms, L1 = 3 H, and C1 = 29 F. Write your answer in Joules.
please solve problems 1 and
problems 2.
PROBLEM 1: Derive state-space equations for the following circuit in the form of L1 where χ = :L2 L3 L1 and (a) y 7 V L3 R1 L1 L3 R3 Vt R2 Vc し2 (c) For Part (a), use the file CircuitStateSpace.slx (define the four matrices in Matlab) to verify your derivation using the following numerical values: R1-1; R3-1 R2-10; L1-1e-3 L3-1e-3 L2-10e-2 ; C1-10e-6 PROBLEM 2: (a) What are eigenvalues of the...
Given the circuit below: R3 C1 Vout C2 R1 R3 Vin R2 ts 1 a) derive the transfer function between the input and the output in terms of R1,C1,R2,C2 b) For this and all other parts below, assume Izl<Ipl, i..e that D(s) is a lead-type compensator. The transfer function is written in the following format ts 1 Express quantities K, z, p using R1,C1,R2,C2 Also, express Κα, α, τ using K,z, p c) Observe the values of s-jw on the...
Q4 (10 marks): What are the values in registers R1, R2 and R3 at the end of this ARMv7 assembly program? MOV R1, #2 MOV R2, #10 MOV R3, #10 L1: CMP R1, R3 BGE L3 BL L2 ADD R1, R1, #3 BL1 L2: ADD R2, R2, #3 MOV R15, R14 L3: MUL R3, R1, R2 Q5 (10 marks): Please write ARMv7 assembly program for following C programs. Assume that variables are stored in memory and their addresses can be...
For the following design L1-2H C1-0.05F R1.4Ω R2-4Ω C2-0.05P L2-2H Va 4cos(10t+90°)V vb-4cos( 10t+90"N R4-4Ω R6:2Ω RS-4Ω Vc-4cos(20t+90jv vds4cos( 10t+60ον (Remember that i) w is given in rad/sec, ii) the above circuits have different Impedances for different frequencies, ii) we replace the shorted voltage power supplies with a short circuit, iV) with atjb the rectangular form and Ad the polar form we have a-Acos(8), b-Asin(θ), A-: va2+1,7 , θ= tan-l (4)if a > 0, θ= 180-tan-IL) if a <0) a)...
Given two capacitors (in Farads) and two inductors (in Henries). C1=10, C2=14, L1=18, and L2=14. a) Determine an equivalent C for C1 and C2 in parallel. b) Determine an equivalent C for C1 and C2 in series. c) Determine an equivalent L for L1 and L2 in parallel. d) Determine an equivalent L for L1 and L2 in series. ans:4
PLEASE HELP IMMEDIATELY
R2 R3 R1 C1 C2 S2 51 In the circuit, the signal frequency f = 1.2 MHz, R1=9 Ohm, R2 = 8 Ohm, R3 = 7 Ohm, C1-22 nF, C2=25 nF; The voltage source Vs1 amplitude and phase are 15 V and 0.12 rad; the voltage source Vs2 amplitude and phase are 4 V and 0.4 rad. (Note the polarity of the voltage sources!) Using nodal analysis, find the following 1) The amplitude of the potential at...
In the circuit shown, R1 = 7 ohm, R2 = 11 ohm, R3 = 9ohm, V1 = 19 V, and V2 = 8V. Find the voltage across R3.
Given R1 = 32, R2 = 62, R3 = 61, i, = 9 A and v, = 3 V. using superposition theorem, find the voltage 1, due only to the current source in the circuit. Us + zs 1 R3 o M. RI R2 Select one: a. 13.5 V b. 187 o c. 9V