[15 total pts] Graphical visualization of a signal's spectrum can help determine the Nyquist rate for...
Problem 4.(30 pts) Given the analog signal x(t) cos(2 cos(3t)+2 sin(4mt) A.(10 pts) Find the Nyquist frequency (sampling frequency) which guarantees That x() can be recovered from it's sampled version xIn] with no aliasing. B.(10 pts) If the sampling period of Ts 0.4 see is used identify all discrete frequencies Of the signal x(t), also indicate if this sampling period is adequate to recover x(t) from xn] C.(10 pts) Suppose signal x(t) is modulated by signal e(t) = cos(2000mt) what...
4. Find the Nyquist rate for the following signals. For each case sketch the magnitude spectrum of the sampled signal if the sampling rate is 25% higher than the Nyquist rate. a.) ft)sinc E 2T 10 b.) h)=sinc 2T For all the following, use ft) given in part a.) c.) glt)= f(l-7) d.) c(t)- f)cos() 1 e.) x(t)= fit)+ _ sinc (t 4. Find the Nyquist rate for the following signals. For each case sketch the magnitude spectrum of the...
1. (15) By the Sampling Theorem the Nyquist sampling rate must be twice the highest bandwidth of the message signal. For the three message signals below determine the Nyquist rate and the Nyquist interval for each. a) m(t) = 0.5 cos(150 ) + sin(300Ft) + 0.75 cos(350ft) b) m(t) = 2 cos(120rt) sin(3007) c) m(t) = sinc(4000) = sin(400m) Recall: the Fourier transform of a sinc waveform is a rectangular pulse
please show steps, focus on part b more 1. (23 points) Sampling and Aliasing. (a) Find the Nyquist sampling rate wn for the given x(t). (Recall that the sampling frequency has to be twice larger than the bandwidth of the signal to recover the signal without loss of information.) i. (5 pts) X(t) = sinc(5000) * cos(7t). ii. (5 pts) r(t) = sin(101) cos(106) iii. (5 pts) (t) = sinc(50000) + cos(56) (b) (8 pts) Let r(t) = sinc(t/h), y(t)...
10. Find the Fourier transform of a continuous-time signal x(t) = 10e Su(t). Plot the magnitude spectrum and the phase spectrum. If the signal is going to be sampled, what should be the minimum sampling frequency so that the aliasing error is less than 0.1 % of the maximum original magnitude at half the sampling frequency. 11. A signal x(t) = 5cos(2nt + 1/6) is sampled at every 0.2 seconds. Find the sequence obtained over the interval 0 st 3...
Signal xo(t) 5 cos (200π1+ 품 ) + 4 sin (300π) is sampled at a rate of Fs = 1 kHz to obtain the discrete-time signal x[n]. (a) Determine the spectrum X(ej ) of x[n] and plot its magnitude as a function of ω rad sam in tad and as a function of F in Hz. Explain whether the original signal xe(t) can be recovered from xln]. (b) Repeat part (a) for 500 Hz. (c) Repeat part (a) for 100...
QUESTION 4 a. Determine the frequency spectrum of the signal x(t) b. What is the Nyquist rate for this signal? cos(t) + 5sn3t. me-invariant system defined by, dt dt what will the system output y(t) be? QUESTION 5 The system function of a casual LTI system is given as, 2s a. Find the impulse response of the system. b. Find the step response of the system. A causal discrete-time LTI system is described by, y[n] - (3/4) yin-1+(1/8) yin-21 xn]...
PROBLEM 2 150 pts.] A signal is consist of three sine functions: the first one, , has a wave frequency of 50 Hz, the second one, 2, has 100 Hz, and the last one, r3, has 200 Hz. However, each function has different amplitude: the amplitude of the first signal component x! is 10 cm, the amplitude of the second signal component xi s 5 cm; and the amplitude of the last signal component t3 is 1 cm. As a...
) + 4 sin(300m), w a) (2 points) Given the signal x(t) = 5 cos(200 period, T, is needed to avoid aliasing? 3. b) (8 points) If you sample x() with sampling period T/2 where T is your answer to part a), what is the resulting discrete signal, x[n]?
onsider the sampling and reconstruction system shown in the figure. x(t) IdealIdeal) D-to-C Converter Converter Assume that the sampling rates of the C-to-D and D-to-C converters are equal, and the input to the Ideal C-to-D converter is x(t) = 2 cos (2m(50)t +π) + cos(2π(150e) a. (5) If the output of the Ideal D-to-C converter is equal to the input x(t) i.e. ()2 cos (2m(50)t +7)+cos(2(150)) b. (5) If the sampling rate is fs = 250 samples/sec, determine the discrete-time...