An unknown resistance (R.) can be measured m terms of a standard (R, ) using this...
The resistance of an RTD is measured with a Wheatstone bridge circuit. To eliminate errors from wiring resistance inaccuracy, RTDs use matched lead wires in a 3-wire or 4-wire bridge circuit. 1. Draw a simple 2wire Wheastonc bridge cret 2. Draw a simple 3-wire Wheatstone bridge circuit. 3. Draw a simpie 4-wire Wheatstone bridge circuit. 4. Explain the advantage of using a 3-wire or 4-wire Wheatstone bridge circuit instead of a 2-wire circuit.
4. To precisely measure the change in the electrical resistance of a strain gauge, we commonly use the Wheatstone bridge. Consider the Wheatstone bridge shown below Derive the expression for Vo in terms of VEx, RI, R2, R3, and R4. Under what condition is the bridge balanced, that is, Vo 0 a. b. Let Resistor 2 represent a strain gauge, whose resistance changes from R2 to R2+ dR2. The resistances of all the other resistors stay fixed. This is called...
An unknown length of platinum wire 1.14 mm in diameter is placed as the unknown resistance in a Wheatstone bridge (see figure). Arms 1 and 2 have resistance of 39.6 92 and 28.8 12, respectively. Balance is achieved when R3 is 3.88 22.(Figure 1) Part A How long is the platinum wire? 190 AED ? Figure C 1 oft m B Rs Submit Request Answer Ammeter Provide Feedback RA 2 D
For a Wheatstone bridge circuit, R1 is a sensor whose resistance is related to a measured variable x by the equation R1 = 20x2. If R3 = R4 = 100 Ω, and the bridge is balanced when R2 = 46 Ω, determine x.
To what value must R3 be adjusted to balance a Wheatstone bridge it the unknown resistance Rx is 155 Ohm. R1 is 46.5 Ohm, and R2 is 185 Ohm? The bridge is said to be balanced when the current through the galvanometer (G) is zero. Number ________ Ohm
EET3122 Quiz3 Name: 1. A DC Wheatstone bridge contains three resistors whose resistance values are constant at, and one component with unknown resistance value. Given V, (a) The output voltage Vo is measured to be 0 V. Determine the resistance of 3000 2.1 300012 AT (b) Suppose the unknown component is a temperature sensor. After temperature increases, the output voltage V, changes from 0 V to 6.2 mV. Determine the resistance of R(T).
P5-Consider a standard strain-gage bridge with R, as the only active gage and R3-R4. Obtain an expression for R, in terms of R2. vo, and vref. Show that when R1-R2. we get v 0 -a balanced bridge- as required. Note that the equation for R. assuming that vo is measured using a high-impedance voltmeter, can be used to detect large resistance changes in R1. Now suppose that the active gage R1 is connected to the bridge using a long, twisted...
7.- The Wheatstone Bridge. The circuit shown in the figure, called a Wheatstone bridge, is used to determine the value of an unknown resistor \(X\) by comparison with three resistors \(M, N\), and \(P\) whose resistances can be varied. For each setting, the resistance of each resistor is precisely known. With switches \(K_{1}\) and \(K_{2}\) closed, these resistors are varied until the current in the galvanometer \(G\) is zero; the bridge is then said to be balanced. (a) Show that...
3. A resistance strain gauge with R-120 ohm and a gauge factor of 2 is placed in an equal-arm Wheatstone bridge in which all the resistances are equal to 120 ohm. If the maximum gauge current is to be 0.05A, what is the maximum allowable bridge excitation voltage?
fast please 2. In the shown Wheatstone bridge circuit, R., and R, are the two portions of a I m single wire with a sliding contact. If the bridge is balanced when L - 46 cm and R, -100 2. What is the value of the unknown resistor R.