Thank You...!!!
pleas help fast Problem #3 (30 points) a. Design an Asynchronous Modulo 9 counter (a counter...
Design serial (asynchronous) counter modulo 7 using synchronous flip-flops (T, D or JK). The counter should count up.
Q3. Synchronous Counter Figure 8.3(a) shows a modulo-8 synchronous up-counter (Modulo-8 because this counter can count only from 0 to 7 with its 3 bits qo, q1 and 92.). Treat each gray cell in the figure as a component and write generic VHDL codes to create a modulo-2N counter, where N is the number of flip-flops required. Use nominal mapping for this problem while instantiating components. When the asynchronous reset signal rst is high, the counter is set to 0...
9) Using JK flip flops and in the space below, design a synchronous counter that counts up from 0 to 5 and recycles to 0. (Positive edge triggered, PRE & CLR active low) Show all connections except the power and ground inputs to the flip flops.
(a) Design an asynchronous Binary Coded Decimal (BCD) count-up counter using JK flip-flops. Draw the counter circuit clearly showing the configuration of the JK flip-flops and the necessary logic gate(s). Sketch the input and output waveforms of this counter (7 Marks) (b) The binary up/down counter for a cargo lift controller in a 7-storey building has an up-down (UID) control input and a buzzer output (B). The buzzer will sound B 1) when the lift is at level 1 or...
2. Synchronous Counters: a. Design a count up/count down counter that counts from 0 up to 4, then 4 down to 0 using D flip flop. b. Design a count up counter that counts from 0 up to 12 using JK flip flops.
Use J-K Flip Flops to design a Asynchronous counter that counts from 0 to 9 and then recycles. Verify your answer by plotting the digital waveforms.
Problem 3:(10 pts) Design a synchronous machine (Transition Table, K-maps, Final Equations, Circuit Diagram) that counts through the following sequence in the order shown below. Note, there are no inputs or output variables, so your Q values must reflect the Hex value listed B 742 D 9 3 0 and repeat a) using all D flip-flops and combinational logic (AND/OR/NOT gates only) b) using all T flip-flops and a multiplexer of size 8:1 Problem 3:(10 pts) Design a synchronous machine...
Can you please help answer b) and c) ? Design a synchronous counter that counts through the following sequence using J-K flip flop. 7+9+1+3+8+0+5+4+6+2+10+12+11+1413 Step of programming: a) Build an Excitation Table b) Create an expression of the flip-flop c) Sketch the circuit based on expression
Up-Down counter with enable using JK flip-flops: Design, construct and test a 2-bit counter that counts up or down. An enable input E determines whether the counter is on or off. If E = 0, the counter is disabled and remains in the present count even though clock pulses are applied to the flip-flops. If E= 1, the counter in enabled and a second input, x, determines the count direction. If x= 1, the circuit counts up with the sequence...
Q2) 4-bit Synchronous Counter Using Proteus, design Synchronous 4 bit Up binary counter using JK flip flops (Use 74HC76 JK flipflop). The circuit count from 0000 to 1111, etc. Experiment procedure: طريقة اجراء التجربة a) Complete the circuit. You can use external gates based on the following conditions: o Flipflop A switches every clock. o Flipflop B switches when the output of flipflop A=1 o Flipflop C switches when the outputs of A-B=1 o Flipflop D switches when the outputs of A=B=C=1 b) What is the typical feature of...